Airtac BSED Clamping Double Acting Cylinder BSED100X900S
The AirTAC Airtac BSED Clamping Double Acting Cylinder BSED100X900S combines a double-rod ISO 15552 cylinder — a Ø25mm rod out BOTH ends for equal force both directions — with an integrated spring-applied, air-released ROD LOCK that holds up to 5500 N in either direction if air is lost. Ø100mm bore, 900mm stroke, PT1/2 ports, G1/8 lock-release.
- BoreØ100 mm
- Stroke900 mm
- Static holding force5500 N
- ConfigurationDouble rod + lock
- Cylinder portPT1/2
- Lock-release portG1/8
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac BSED Clamping Double Acting Cylinder BSED100X900S
The AirTAC BSED100X900S is a double-acting, double-rod ISO 15552 profile cylinder featuring an integrated spring-applied, air-released rod lock. A rod exits both ends, delivering equal drive force of 3681 N each way at 0.5 MPa. The fail-safe collet mechanism provides a 5500 N static holding force with no live air required.
This 100 mm bore unit operates at 0.15-0.7 MPa with a PT1/2 cylinder port and a dedicated G1/8 release port. Equipped with a magnet (-S), it supports CMSE reed and DMSE electronic sensors. The extruded aluminum barrel design eliminates external tie rods while maintaining ISO 15552 mounting interchangeability.
Double Rod + 5500 N Rod Lock (Ø100mm)
A rod exits both ends for symmetric force and back-rod tooling, and a spring clamps the collet so the Airtac BSED Clamping Double Acting Cylinder BSED100X900S holds its position in both directions on air loss or E-stop. Apply 0.15–0.7 MPa to the G1/8 release port to unlock. Engage only after the rod has stopped (not a dynamic brake), and release only when both piston sides are pressure-balanced; allow ≥0.5 s for full release.
Airtac BSED Clamping Double Acting Cylinder BSED100X900S Technical Specifications
| Model | Airtac BSED Clamping Double Acting Cylinder BSED100X900S |
|---|---|
| Series | BSED ISO 15552 double-rod rod-lock cylinder |
| Bore size | Ø100 mm |
| Stroke | 900 mm |
| Static holding force | 5500 N |
| Cylinder port | PT1/2 |
| Lock-release port | G1/8 |
| Configuration | Double rod, double acting |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Unlocking pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC BSED datasheet. Rod thread M20×1.5 both ends. Mounting (BSED): Basic, LB, FA, TC. Port options: PT (standard) / G (BSPP); lock-release port is G1/8.
Theoretical Output Force (Ø100mm)
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa (max) | 5154 N |
| Max drive (@0.7 MPa) | 526 kgf |
A rod exits both ends, so force is equal on extend and retract. Drive force is separate from the 5500 N static lock holding force. Size with a safety margin.
Model Code: Airtac BSED Clamping Double Acting Cylinder BSED100X900S
| B | Rod-lock cylinder prefix. |
|---|---|
| SED | ISO 15552 double-rod double-acting body. |
| 100 | Bore size in mm. |
| ×900 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Thread: PT (blank) / G. Mounting (BSED): Basic, LB, FA, TC. Related: SED (double rod, no lock), BSE (single-rod rod lock). Sensors CMSE/DMSE fit magnetic BSED.
Where the Airtac BSED Clamping Double Acting Cylinder BSED100X900S Is Used
Vertical Lift Jigs
Holds elevated 5000 N vertical lifting jigs securely in place during air loss, while the 5153 N equal both-way drive powers rapid up/down cycling.
Pallet Stops
Arrests heavy pallet conveyor flows using the 5500 N fail-safe collet, utilizing the twin rods to mount dual stop flags without rotational twist.
Indexing Chucks
Drives 900 mm chuck actuation with identical force in both directions, locking the 525 kgf payload instantly when the machine E-stop trips.
Is the Airtac BSED Clamping Double Acting Cylinder BSED100X900S the Right Cylinder?
Select this 100 mm bore model when an application demands both symmetric pushing/pulling force and intermediate fail-safe holding. Verify your static load does not exceed the 5500 N holding capacity. If you need less force, the 80 mm bore offers 2268 N at 0.5 MPa and 3600 N holding; for heavier loads, the 125 mm bore provides 5734 N at 0.5 MPa and 8600 N holding.
At 900 mm stroke, use a guide rail to prevent side-load binding on the seals. Engage the lock only after the rod completely stops, and release it only when both piston sides are pressure-balanced, allowing at least 0.5 seconds. Replacement requires matching the 100 mm bore, 900 mm stroke, PT thread, and Basic/LB/FA/TC mounting.
Quick checklist
- ✓ Need both symmetric force AND fail-safe hold?
- ✓ Load to hold ≤ 5500 N?
- ✓ Back-rod space for tooling/flag
- ✓ Lock engaged only when stopped
- ✓ G1/8 release-air line available
Installation & Safety Notes
- check Engage the lock only after the rod has stopped — not a dynamic brake.
- check Release only when both piston sides are pressure-balanced.
- check Allow ≥0.5 s for full release before commanding motion.
- check Feed the G1/8 release port with 0.15–0.7 MPa clean air.
- check Support both rod ends; avoid side load.
- check Use BSED mounting (Basic/LB/FA/TC).
Airtac BSED Clamping Double Acting Cylinder BSED100X900S FAQ
The integrated spring-applied collet instantly clamps the rod, providing a 5500 N bidirectional static hold with no live air. It is a fail-safe holding lock, not a dynamic brake, so engage it only after the rod stops.
The drive force is equal both ways at 3681 N (0.5 MPa) and 5153 N (0.7 MPa), with a maximum drive of 525 kgf. The static holding force of the lock is 5500 N. Release the lock via the G1/8 port only when both sides are pressure-balanced.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC BSED Cylinders
Request a Quote for Airtac BSED Clamping Double Acting Cylinder BSED100X900S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.