Airtac BSED Clamping Double Acting Cylinder BSED63X250S
The AirTAC Airtac BSED Clamping Double Acting Cylinder BSED63X250S combines a double-rod ISO 15552 cylinder — a Ø20mm rod out BOTH ends for equal force both directions — with an integrated spring-applied, air-released ROD LOCK that holds up to 2200 N in either direction if air is lost. Ø63mm bore, 250mm stroke, PT3/8 ports, G1/8 lock-release.
- BoreØ63 mm
- Stroke250 mm
- Static holding force2200 N
- ConfigurationDouble rod + lock
- Cylinder portPT3/8
- Lock-release portG1/8
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac BSED Clamping Double Acting Cylinder BSED63X250S
The AirTAC BSED63X250S is a double-acting, double-rod ISO 15552 profile cylinder with an integrated spring-applied, air-released rod lock. A rod exits both ends, yielding equal thrust in both directions at about 1402 N each way at 0.5 MPa. The collet lock provides a bidirectional static holding force of 2200 N.
Because the lock engages mechanically without live air, the rod is securely clamped during pressure loss or E-stop trips. The -S magnet enables position feedback via CMSE reed or DMSE electronic sensors, while the rear rod resists rotation and can mount a flag or cam.
Double Rod + 2200 N Rod Lock (Ø63mm)
A rod exits both ends for symmetric force and back-rod tooling, and a spring clamps the collet so the Airtac BSED Clamping Double Acting Cylinder BSED63X250S holds its position in both directions on air loss or E-stop. Apply 0.15–0.7 MPa to the G1/8 release port to unlock. Engage only after the rod has stopped (not a dynamic brake), and release only when both piston sides are pressure-balanced; allow ≥0.5 s for full release.
Airtac BSED Clamping Double Acting Cylinder BSED63X250S Technical Specifications
| Model | Airtac BSED Clamping Double Acting Cylinder BSED63X250S |
|---|---|
| Series | BSED ISO 15552 double-rod rod-lock cylinder |
| Bore size | Ø63 mm |
| Stroke | 250 mm |
| Static holding force | 2200 N |
| Cylinder port | PT3/8 |
| Lock-release port | G1/8 |
| Configuration | Double rod, double acting |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Unlocking pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC BSED datasheet. Rod thread M16×1.5 both ends. Mounting (BSED): Basic, LB, FA, TC. Port options: PT (standard) / G (BSPP); lock-release port is G1/8.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa (max) | 1962 N |
| Max drive (@0.7 MPa) | 200 kgf |
A rod exits both ends, so force is equal on extend and retract. Drive force is separate from the 2200 N static lock holding force. Size with a safety margin.
Model Code: Airtac BSED Clamping Double Acting Cylinder BSED63X250S
| B | Rod-lock cylinder prefix. |
|---|---|
| SED | ISO 15552 double-rod double-acting body. |
| 63 | Bore size in mm. |
| ×250 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Thread: PT (blank) / G. Mounting (BSED): Basic, LB, FA, TC. Related: SED (double rod, no lock), BSE (single-rod rod lock). Sensors CMSE/DMSE fit magnetic BSED.
Where the Airtac BSED Clamping Double Acting Cylinder BSED63X250S Is Used
Elevating Lift Stations
Holds a 2200N vertical load securely mid-stroke without live air, while the 1962N both-way drive raises and lowers the platform smoothly.
Dual-End Tooling Jigs
Uses the equal both-way force for machining pressure, while the rear rod provides anti-rotation stability for a position flag.
Pallet Diverters
Clamps the diverter arm instantly upon E-stop activation, securely freezing the 63mm bore position during emergency halts.
Is the Airtac BSED Clamping Double Acting Cylinder BSED63X250S the Right Cylinder?
Select this 63mm bore when an application demands symmetric 1962 N drive force at 0.7 MPa alongside a 2200N fail-safe hold. If your load requires less force, the 50mm bore offers 825 N at 0.5 MPa and a 1400 N hold; stepping up to the 80mm bore provides 2268 N at 0.5 MPa and a 3600 N hold.
Always verify the load to hold is at or below 2200 N. Engage the lock only after the rod stops, and release it only when both piston sides are pressure-balanced, allowing at least 0.5 seconds. For replacement, match the 63mm bore, 250mm stroke, PT3/8 port, and -S magnet. At 250mm stroke, use guide rails to manage side loads.
Quick checklist
- ✓ Need both symmetric force AND fail-safe hold?
- ✓ Load to hold ≤ 2200 N?
- ✓ Back-rod space for tooling/flag
- ✓ Lock engaged only when stopped
- ✓ G1/8 release-air line available
Installation & Safety Notes
- check Engage the lock only after the rod has stopped — not a dynamic brake.
- check Release only when both piston sides are pressure-balanced.
- check Allow ≥0.5 s for full release before commanding motion.
- check Feed the G1/8 release port with 0.15–0.7 MPa clean air.
- check Support both rod ends; avoid side load.
- check Use BSED mounting (Basic/LB/FA/TC).
Airtac BSED Clamping Double Acting Cylinder BSED63X250S FAQ
The integrated spring-applied collet clamps the rod immediately, providing a 2200N static holding force to prevent movement. It is a fail-safe hold, not a dynamic brake, so it must engage only after the rod stops.
The double-rod design provides equal drive force both ways: 1402N at 0.5 MPa, 1962N at 0.7 MPa, and a maximum drive of 200 kgf. The fail-safe rod lock adds a bidirectional static holding force of 2200N.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC BSED Cylinders
Request a Quote for Airtac BSED Clamping Double Acting Cylinder BSED63X250S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.