Airtac BSED Clamping Double Acting Cylinder BSED63X600
The AirTAC Airtac BSED Clamping Double Acting Cylinder BSED63X600 combines a double-rod ISO 15552 cylinder — a Ø20mm rod out BOTH ends for equal force both directions — with an integrated spring-applied, air-released ROD LOCK that holds up to 2200 N in either direction if air is lost. Ø63mm bore, 600mm stroke, PT3/8 ports, G1/8 lock-release.
- BoreØ63 mm
- Stroke600 mm
- Static holding force2200 N
- ConfigurationDouble rod + lock
- Cylinder portPT3/8
- Lock-release portG1/8
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac BSED Clamping Double Acting Cylinder BSED63X600
The AirTAC BSED63X600 is a double-acting, double-rod ISO 15552 profile cylinder featuring an integrated spring-applied, air-released rod lock. A rod exits both ends, delivering equal drive force in both directions—about 1402 N each way at 0.5 MPa and 1962 N at 0.7 MPa. The extruded aluminum barrel provides ISO 15552 dimensional interchangeability without external tie rods.
This fail-safe collet lock provides a 2200 N static holding force with no live air required. It engages bidirectionally when pressure is lost or an E-stop trips, holding the rod securely at position. The lock is not a dynamic brake; engage it only after the rod stops, and release it only when both piston sides are pressure-balanced, allowing at least 0.5 seconds. This SKU has no magnet, so position sensing is not available.
Double Rod + 2200 N Rod Lock (Ø63mm)
A rod exits both ends for symmetric force and back-rod tooling, and a spring clamps the collet so the Airtac BSED Clamping Double Acting Cylinder BSED63X600 holds its position in both directions on air loss or E-stop. Apply 0.15–0.7 MPa to the G1/8 release port to unlock. Engage only after the rod has stopped (not a dynamic brake), and release only when both piston sides are pressure-balanced; allow ≥0.5 s for full release.
Airtac BSED Clamping Double Acting Cylinder BSED63X600 Technical Specifications
| Model | Airtac BSED Clamping Double Acting Cylinder BSED63X600 |
|---|---|
| Series | BSED ISO 15552 double-rod rod-lock cylinder |
| Bore size | Ø63 mm |
| Stroke | 600 mm |
| Static holding force | 2200 N |
| Cylinder port | PT3/8 |
| Lock-release port | G1/8 |
| Configuration | Double rod, double acting |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Unlocking pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC BSED datasheet. Rod thread M16×1.5 both ends. Mounting (BSED): Basic, LB, FA, TC. Port options: PT (standard) / G (BSPP); lock-release port is G1/8.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa (max) | 1962 N |
| Max drive (@0.7 MPa) | 200 kgf |
A rod exits both ends, so force is equal on extend and retract. Drive force is separate from the 2200 N static lock holding force. Size with a safety margin.
Model Code: Airtac BSED Clamping Double Acting Cylinder BSED63X600
| B | Rod-lock cylinder prefix. |
|---|---|
| SED | ISO 15552 double-rod double-acting body. |
| 63 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Thread: PT (blank) / G. Mounting (BSED): Basic, LB, FA, TC. Related: SED (double rod, no lock), BSE (single-rod rod lock). Sensors CMSE/DMSE fit magnetic BSED.
Where the Airtac BSED Clamping Double Acting Cylinder BSED63X600 Is Used
Vertical Lift Stages
Uses the 2200 N fail-safe lock to hold a 100 kg vertical lift platform securely in place during an air loss event, while the 1962 N both-way drive force raises and lowers the load.
Pallet Stopper Gates
Employs the double-rod design to mount a stopper flag on the rear rod for a conveyor line, utilizing the equal both-way motion to actuate the gate without rotational torque.
Machining Center Indexing
Clamps a mid-stroke machining fixture using the 2200 N spring-applied collet, ensuring the 600 mm stroke position remains rigidly fixed during a cutting cycle with zero live air.
Is the Airtac BSED Clamping Double Acting Cylinder BSED63X600 the Right Cylinder?
Select this 63 mm bore model when an application requires symmetric both-way force and intermediate fail-safe holding. Verify your static load does not exceed the 2200 N holding force. If you need less drive force, the 50 mm bore offers 825 N at 0.5 MPa and a 1400 N hold; if you need more, the 80 mm bore provides 2268 N at 0.5 MPa and a 3600 N hold. Operating pressure is capped at 0.7 MPa.
With a 600 mm stroke, use a guide rail to prevent side-load damage to the seals and rod lock collet. When ordering a replacement, match the 63 mm bore, 600 mm stroke, PT3/8 cylinder port, G1/8 release port, and the mounting style (Basic, LB, FA, or TC).
Quick checklist
- ✓ Need both symmetric force AND fail-safe hold?
- ✓ Load to hold ≤ 2200 N?
- ✓ Back-rod space for tooling/flag
- ✓ Lock engaged only when stopped
- ✓ G1/8 release-air line available
Installation & Safety Notes
- check Engage the lock only after the rod has stopped — not a dynamic brake.
- check Release only when both piston sides are pressure-balanced.
- check Allow ≥0.5 s for full release before commanding motion.
- check Feed the G1/8 release port with 0.15–0.7 MPa clean air.
- check Support both rod ends; avoid side load.
- check Use BSED mounting (Basic/LB/FA/TC).
Airtac BSED Clamping Double Acting Cylinder BSED63X600 FAQ
The double-rod drive force is equal both ways: 1402 N at 0.5 MPa and 1962 N at 0.7 MPa, with a maximum drive of 200 kgf. The integrated fail-safe rod lock provides a separate 2200 N static holding force.
The lock is spring-applied and air-released via the G1/8 port. You must release it only after the rod has completely stopped moving and both piston sides are pressure-balanced, allowing at least 0.5 seconds for the collet to disengage.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC BSED Cylinders
Request a Quote for Airtac BSED Clamping Double Acting Cylinder BSED63X600
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.