Airtac BSED Clamping Double Acting Cylinder BSED80X600S
The AirTAC BSED Clamping Double Acting Cylinder BSED80X600S combines a double-rod ISO 15552 cylinder — a Ø25mm rod out BOTH ends for equal force both directions — with an integrated spring-applied, air-released ROD LOCK that holds up to 3600 N in either direction if air is lost. Ø80mm bore, 600mm stroke, PT3/8 ports, G1/8 lock-release.
- BoreØ80 mm
- Stroke600 mm
- Static holding force3600 N
- ConfigurationDouble rod + lock
- Cylinder portPT3/8
- Lock-release portG1/8
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac BSED Clamping Double Acting Cylinder BSED80X600S
The AirTAC BSED80X600S is a double-acting, double-rod ISO 15552 profile cylinder with an integrated spring-applied, air-released rod lock. A rod exits both ends, delivering equal force and speed in both directions. The integrated collet lock provides a bidirectional static holding force of 3600 N, clamping the rod securely whenever air is lost or an E-stop is triggered.
This 80mm bore model generates 2268 N each way at 0.5 MPa and 3175 N at 0.7 MPa. It features a 25mm rod, an M20x1.5 rod-end thread, and a PT3/8 cylinder port. The separate G1/8 release port controls the lock, which is a static holding device, not a dynamic brake. The -S magnet option supports CMSE reed and DMSE electronic sensors for position feedback.
Double Rod + 3600 N Rod Lock (Ø80mm)
A rod exits both ends for symmetric force and back-rod tooling, and a spring clamps the collet so the Airtac BSED Clamping Double Acting Cylinder BSED80X600S holds its position in both directions on air loss or E-stop. Apply 0.15–0.7 MPa to the G1/8 release port to unlock. Engage only after the rod has stopped (not a dynamic brake), and release only when both piston sides are pressure-balanced; allow ≥0.5 s for full release.
Airtac BSED Clamping Double Acting Cylinder BSED80X600S Technical Specifications
| Model | Airtac BSED Clamping Double Acting Cylinder BSED80X600S |
|---|---|
| Series | BSED ISO 15552 double-rod rod-lock cylinder |
| Bore size | Ø80 mm |
| Stroke | 600 mm |
| Static holding force | 3600 N |
| Cylinder port | PT3/8 |
| Lock-release port | G1/8 |
| Configuration | Double rod, double acting |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Unlocking pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC BSED datasheet. Rod thread M20×1.5 both ends. Mounting (BSED): Basic, LB, FA, TC. Port options: PT (standard) / G (BSPP); lock-release port is G1/8.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 2268 N |
| 0.7 MPa (max) | 3175 N |
| Max drive (@0.7 MPa) | 324 kgf |
A rod exits both ends, so force is equal on extend and retract. Drive force is separate from the 3600 N static lock holding force. Size with a safety margin.
Model Code: Airtac BSED Clamping Double Acting Cylinder BSED80X600S
| B | Rod-lock cylinder prefix. |
|---|---|
| SED | ISO 15552 double-rod double-acting body. |
| 80 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Thread: PT (blank) / G. Mounting (BSED): Basic, LB, FA, TC. Related: SED (double rod, no lock), BSE (single-rod rod lock). Sensors CMSE/DMSE fit magnetic BSED.
Where the Airtac BSED Clamping Double Acting Cylinder BSED80X600S Is Used
Overhead Z-Axis Lifts
Holds a 3600 N vertical load safely during air loss while providing 3175 N of equal lifting and lowering force.
Dual-Tool Machining
Uses the rear rod for a flag cam while driving 2268 N both ways at 0.5 MPa for symmetric tool actuation.
Heavy Pallet Stops
Locks a 600mm stroke in place instantly to halt pallet flow, resisting 324 kgf of maximum drive force.
Is the Airtac BSED Clamping Double Acting Cylinder BSED80X600S the Right Cylinder?
Select this model when your application demands symmetric both-way force and fail-safe holding without live air. Verify your load does not exceed the 3600 N holding force. If your load is lighter, the 63mm bore offers 1402 N at 0.5 MPa with a 2200 N hold; for heavier loads, the 100mm bore provides 3681 N at 0.5 MPa and a 5500 N hold. Always engage the lock only after the rod stops and release it only when both piston sides are pressure-balanced, allowing at least 0.5 seconds.
For a 600mm stroke, use a guide to manage side loads and prevent rod binding. When ordering a replacement, match the 80mm bore, 600mm stroke, PT3/8 port, and -S magnet. Mounting options are restricted to Basic, LB, FA, and TC.
Quick checklist
- ✓ Need both symmetric force AND fail-safe hold?
- ✓ Load to hold ≤ 3600 N?
- ✓ Back-rod space for tooling/flag
- ✓ Lock engaged only when stopped
- ✓ G1/8 release-air line available
Installation & Safety Notes
- check Engage the lock only after the rod has stopped — not a dynamic brake.
- check Release only when both piston sides are pressure-balanced.
- check Allow ≥0.5 s for full release before commanding motion.
- check Feed the G1/8 release port with 0.15–0.7 MPa clean air.
- check Support both rod ends; avoid side load.
- check Use BSED mounting (Basic/LB/FA/TC).
Airtac BSED Clamping Double Acting Cylinder BSED80X600S FAQ
The spring-applied collet engages instantly, providing a 3600 N bidirectional static hold with no live air. It is a holding lock, not a dynamic brake, so engage it only after the rod stops.
The double-rod design provides equal force both ways: 2268 N at 0.5 MPa, 3175 N at 0.7 MPa, and a maximum drive of 324 kgf. The separate static holding force of the lock is 3600 N.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC BSED Cylinders
Request a Quote for Airtac BSED Clamping Double Acting Cylinder BSED80X600S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.