Airtac JSI Series Standard Cylinder JSI100X1500S
The AirTAC Airtac JSI Series Standard Cylinder JSI100X1500S is a genuine double acting JIS-standard air cylinder with a Ø100mm bore and 1500mm stroke, G1/2 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ100 mm
- Stroke1500 mm
- Port sizeG1/2
- Acting typeDouble acting
- Rod threadM26×1.5
- CushionAdjustable, 33 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSI Series Standard Cylinder JSI100X1500S
Delivering 3927 N of push force at 0.5 MPa, this double-acting JIS-standard profile cylinder saves valuable machine space by being noticeably shorter than an ISO 15552 cylinder of the same 100 mm bore. The extruded hard-anodized aluminum barrel omits external rods to resist wear, while the two-way piston seal retains grease for a long, low-friction service life. Because the -S suffix provides a built-in magnet, you can drop CMSE or DMSE reed and electronic switches directly into the side grooves for position sensing.
For practical sizing, plan for about 2356 N of real work at 0.5 MPa, which means it lifts roughly 200 kg vertically with a 2:1 safety margin. The G1/2 air port feeds the 32 mm hard-chrome rod, and adjustable 33 mm air cushions at both ends decelerate the piston smoothly across its 1500 mm travel. If you need dual-rod thrust or adjustable end-positions, consider the related JSID or JSIJ variants.
Airtac JSI Series Standard Cylinder JSI100X1500S Technical Specifications
| Model | Airtac JSI Series Standard Cylinder JSI100X1500S |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 1500 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M26×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 33 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac JSI Series Standard Cylinder JSI100X1500S
| JSI | JIS-standard profile cylinder (double-acting type). |
|---|---|
| 100 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×1500 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSI Series Standard Cylinder JSI100X1500S Is Used
Automotive Panel Transfer
Pushes heavy stamped metal doors between welding stations, utilizing the full 3927 N thrust at 0.5 MPa to overcome conveyor friction.
Palletized Goods Ejector
Ejects 200 kg packaged assemblies from a stretch-wrap machine, relying on the 1500 mm stroke to clear the loading zone completely.
Injection Mold Extraction
Extracts large molded plastic bins from presses, where the hard-anodized barrel withstands repeated high-impact cycling and factory debris.
Is the Airtac JSI Series Standard Cylinder JSI100X1500S the Right Cylinder?
When sizing this 100 mm bore, check both neighbors: a 63 mm bore gives 1559 N push at 0.5 MPa, while a 125 mm bore yields 6136 N. This model hits 3927 N, making it ideal for heavy-duty positioning. Since the stroke is 1500 mm, you must use an external guide to prevent rod bending and excessive side loads. Remember that a standard cylinder drifts when air is lost or the valve is centered; the cushions only decelerate the piston near stroke end and will not hold a load. For vertical or suspended loads, install an external rod lock or a pilot-operated check valve. The -S magnet matches CMSE/DMSE sensors perfectly.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSI Series Standard Cylinder JSI100X1500S FAQ
At 0.5 MPa it provides 3927 N push and 3574 N pull. At 0.7 MPa it provides 5497 N push and 5003 N pull. The theoretical maximum force is 801 kgf at 1.0 MPa. The air port is G1/2, the rod is 32 mm, and the rod-end thread is M26x1.5.
It is a JIS-standard profile cylinder that is shorter and more compact than an ISO 15552 cylinder of the same bore. The -S suffix means it has a built-in piston magnet, allowing CMSE or DMSE switches to be installed in the side grooves for precise position detection.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSI Series Standard Cylinder JSI100X1500S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.