Airtac JSI Series Standard Cylinder JSI100X80STC
The AirTAC Airtac JSI Series Standard Cylinder JSI100X80STC is a genuine double acting JIS-standard air cylinder with a Ø100mm bore and 80mm stroke, G1/2 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ100 mm
- Stroke80 mm
- Port sizeG1/2
- Acting typeDouble acting
- Rod threadM26×1.5
- CushionAdjustable, 33 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSI Series Standard Cylinder JSI100X80STC
Delivering 3927 N of push force at 0.5 MPa, the AirTAC JSI100X80STC is a double-acting JIS-standard profile cylinder built for heavy-duty automation. Its extruded hard-anodized aluminum barrel omits external rods entirely, making it significantly shorter and more compact than an equivalent ISO 15552 cylinder of the same 100 mm bore. The internal two-way piston seal retains grease for low-friction longevity, while the 80 mm stroke operates at speeds of 30-800 mm/s.
This specific SKU includes a built-in piston magnet (-S) for direct mounting of CMSE or DMSE electronic switches into the side sensor grooves. It also features a TC trunnion mount interface. With a 60 percent safety factor, expect about 2356 N of real working load at 0.5 MPa, which translates to lifting roughly 200 kg vertically with a 2:1 margin. The G1/2 air port handles the necessary volume for this high-force actuator.
Airtac JSI Series Standard Cylinder JSI100X80STC Technical Specifications
| Model | Airtac JSI Series Standard Cylinder JSI100X80STC |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 80 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M26×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 33 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac JSI Series Standard Cylinder JSI100X80STC
| JSI | JIS-standard profile cylinder (double-acting type). |
|---|---|
| 100 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×80 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSI Series Standard Cylinder JSI100X80STC Is Used
Automotive Body Welding
Clamps heavy chassis fixtures with 3927 N of push force at 0.5 MPa, ensuring rigid panel alignment during robotic spot welding.
Pallet Diverting
Uses the TC trunnion mount to articulate a heavy diverter arm, smoothly routing loaded pallets at speeds up to 800 mm/s.
Press Feed Ejection
Exerts up to 801 kgf of theoretical max force to eject dense metal blanks from a stamping press bed in under a second.
Is the Airtac JSI Series Standard Cylinder JSI100X80STC the Right Cylinder?
When sizing this 100 mm bore actuator, verify your force requirements against its neighbors: a 125 mm bore yields 6136 N push at 0.5 MPa, whereas stepping down to an 80 mm bore provides 2513 N. The TC trunnion mount supplied with this unit allows pivoting articulation, ideal for mid-stroke radial loads. Because the -S magnet is present, you can easily integrate position sensing. At an 80 mm stroke, rod-bending stress is minimal, but always ensure the load is guided to prevent side-load damage. Remember that standard air cushions only decelerate the piston near the stroke ends; they do not function as a brake. If your application must hold a vertical load during air loss or valve centering, the piston will drift, requiring an external rod lock or a pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSI Series Standard Cylinder JSI100X80STC FAQ
The 100 mm bore generates 3927 N push and 3574 N pull at 0.5 MPa, 5497 N push and 5003 N pull at 0.7 MPa, and a theoretical maximum of 801 kgf at 1.0 MPa. The air port is G1/2, the rod is 32 mm with an M26x1.5 thread, and the adjustable cushion stroke is 33 mm.
It is a JIS-standard profile cylinder that is shorter and more compact than an ISO 15552 cylinder of the same bore, saving machine space. It uses a hard-anodized aluminum extruded barrel with no external rods, and this STC version includes a TC trunnion mount and an -S magnet for CMSE/DMSE sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSI Series Standard Cylinder JSI100X80STC
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.