Airtac JSI Series Standard Cylinder JSI32X100
The AirTAC Airtac JSI Series Standard Cylinder JSI32X100 is a genuine double acting JIS-standard air cylinder with a Ø32mm bore and 100mm stroke, G1/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ32 mm
- Stroke100 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 20 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSI Series Standard Cylinder JSI32X100
Delivering 402 N of push force at 0.5 MPa, this double-acting 32 mm bore JIS-standard profile cylinder fits where space is tight. It is intentionally shorter and more compact than an ISO 15552 cylinder of the same bore, saving valuable machine real estate. The extruded hard-anodized aluminum barrel sheds external rods to resist wear, while the two-way piston seal retains grease for a long, low-friction service life.
Because this specific SKU lacks the -S magnet, it cannot host CMSE or DMSE position switches. For real-world sizing, plan for about 241 N of actual work at 0.5 MPa, which equates to lifting roughly 20 kg vertically with a 2:1 safety margin. It features a G1/8 port and adjustable air cushions at both ends to smooth out the 100 mm stroke.
Airtac JSI Series Standard Cylinder JSI32X100 Technical Specifications
| Model | Airtac JSI Series Standard Cylinder JSI32X100 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 20 mm |
| Max standard stroke | Up to 1000 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac JSI Series Standard Cylinder JSI32X100
| JSI | JIS-standard profile cylinder (double-acting type). |
|---|---|
| 32 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSI Series Standard Cylinder JSI32X100 Is Used
Small Part Ejection
Pushes lightweight plastic mouldings out of an injection press using 402 N of force at 0.5 MPa.
Package Diverting
Actuates a short 100 mm stroke diverter arm to route small cardboard cartons on a packing line.
Clamp Actuation
Secures thin electronic PCBs during soldering, safely lifting parts under 20 kg with a 2:1 margin.
Is the Airtac JSI Series Standard Cylinder JSI32X100 the Right Cylinder?
If 402 N of push at 0.5 MPa is insufficient, step up to the JSI40 bore for 628 N; if you need less force, the 32 mm bore is the smallest available JSI size. Remember that a standard cylinder drifts when air is lost or the valve centers—the end cushions only decelerate the piston, so add an external rod lock or pilot-operated check valve if you must hold a load. Since this unit has no -S magnet, choose a magnet-equipped variant if you require CMSE or DMSE sensing. At a 100 mm stroke, side-load risks are minimal, but always guide the rod to prevent binding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSI Series Standard Cylinder JSI32X100 FAQ
The JSI32X100 delivers 402 N push and 345 N pull at 0.5 MPa, 563 N push and 483 N pull at 0.7 MPa, with a theoretical maximum of 82 kgf at 1.0 MPa. It uses a G1/8 air port, a 12 mm rod with an M10x1.25 thread, and operates at 30-800 mm/s.
It is a JIS-standard profile cylinder that is shorter and more compact than an ISO 15552 cylinder of the same 32 mm bore. This specific SKU lacks the -S magnet, meaning it cannot accept CMSE or DMSE sensors; you must select the -S variant for switch readiness.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSI Series Standard Cylinder JSI32X100
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.