Airtac JSI Series Standard Cylinder JSI32X175S
The AirTAC Airtac JSI Series Standard Cylinder JSI32X175S is a genuine double acting JIS-standard air cylinder with a Ø32mm bore and 175mm stroke, G1/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ32 mm
- Stroke175 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 20 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSI Series Standard Cylinder JSI32X175S
Delivering 402 N of push force at 0.5 MPa, the AirTAC JSI32X175S is a double-acting JIS-standard profile cylinder built for tight machinery. Its extruded hard-anodized aluminum barrel omits external rods, making it shorter and more compact than an ISO 15552 cylinder of the same 32 mm bore. The two-way piston seal retains grease for extended, low-friction operation.
Because the -S suffix provides a piston magnet, you can drop CMSE or DMSE reed and electronic switches directly into the side grooves for position sensing. Plan for roughly 241 N of real work at 0.5 MPa, which translates to lifting about 20 kg vertically with a 2:1 safety margin. The unit features a G1/8 port, an M10x1.25 rod thread, and adjustable air cushions at both ends.
Airtac JSI Series Standard Cylinder JSI32X175S Technical Specifications
| Model | Airtac JSI Series Standard Cylinder JSI32X175S |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 175 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 20 mm |
| Max standard stroke | Up to 1000 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac JSI Series Standard Cylinder JSI32X175S
| JSI | JIS-standard profile cylinder (double-acting type). |
|---|---|
| 32 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×175 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSI Series Standard Cylinder JSI32X175S Is Used
Small Part Ejection
Provides the 402 N push needed to eject molded plastic parts from a 32 mm bore assembly station without consuming excessive footprint.
Light Diverter Arm
Drives a 175 mm stroke diverter gate on a packaging line, using the built-in magnet to confirm gate position via DMSE sensors.
Clamp Actuation
Actuates a lightweight machining clamp, where the compact profile leaves valuable clearance for spindle access.
Is the Airtac JSI Series Standard Cylinder JSI32X175S the Right Cylinder?
If you need slightly less force, there is no smaller JSI bore available, so this 32 mm bore is the floor of the range. Stepping up to the JSI40X175S raises the push force to 628 N at 0.5 MPa if your 402 N capacity is insufficient. Remember that a standard cylinder drifts if air pressure drops or the valve centers; the adjustable cushion only decelerates the piston near stroke end and will not lock the load. For secure vertical holding, install an external rod lock or a pilot-operated check valve. With 175 mm of travel, side loads are moderate, but ensure your mounting—whether LB foot, FA flange, or TC trunnion—keeps the rod aligned to prevent premature seal wear.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSI Series Standard Cylinder JSI32X175S FAQ
The JSI32X175S delivers 402 N push and 345 N pull at 0.5 MPa, 563 N push and 483 N pull at 0.7 MPa, with a theoretical maximum of 82 kgf at 1.0 MPa. It uses a G1/8 air port and runs at 30-800 mm/s.
The JSI is a JIS-standard profile cylinder that is shorter and more compact than an ISO 15552 cylinder of the same 32 mm bore. It uses an extruded aluminum barrel without external rods to save space on machinery.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSI Series Standard Cylinder JSI32X175S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.