Airtac JSI Series Standard Cylinder JSI32X570S
The AirTAC Airtac JSI Series Standard Cylinder JSI32X570S is a genuine double acting JIS-standard air cylinder with a Ø32mm bore and 570mm stroke, G1/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ32 mm
- Stroke570 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 20 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSI Series Standard Cylinder JSI32X570S
Generating 402 N of push force at 0.5 MPa, this double-acting JIS-standard profile cylinder saves valuable machine space by being noticeably shorter than an ISO 15552 cylinder of the same 32 mm bore. The extruded hard-anodized aluminum barrel omits external rods to resist wear, while the two-way piston seal retains grease for a long, low-friction service life. Air connects via a G1/8 port.
Plan for about 241 N of real work at 0.5 MPa, which translates to lifting roughly 20 kg vertically with a 2:1 safety margin. Because this SKU includes the -S magnet, you can drop CMSE or DMSE reed and electronic switches directly into the side sensor grooves for position detection across the 570 mm travel.
Airtac JSI Series Standard Cylinder JSI32X570S Technical Specifications
| Model | Airtac JSI Series Standard Cylinder JSI32X570S |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 570 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 20 mm |
| Max standard stroke | Up to 1000 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac JSI Series Standard Cylinder JSI32X570S
| JSI | JIS-standard profile cylinder (double-acting type). |
|---|---|
| 32 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×570 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSI Series Standard Cylinder JSI32X570S Is Used
Light-Part Ejection
Pushes small plastic molded parts out of a machining fixture using 402 N of thrust at 0.5 MPa over a 570 mm extraction distance.
Sorter Diverter
Actuates a routing gate on a packaging conveyor, where the built-in -S magnet triggers DMSE sensors to confirm full extension.
Vertical Tray Lift
Lifts approximately 20 kg material trays vertically between processing tiers, relying on the compact JIS profile to fit tight vertical spaces.
Is the Airtac JSI Series Standard Cylinder JSI32X570S the Right Cylinder?
If you need less push, there is no smaller JSI bore; stepping up to the 40 mm bore raises the 0.5 MPa push force to 628 N. Remember that a standard cylinder drifts if air is lost or the valve centers, as the adjustable air cushion only decelerates the piston near stroke end rather than locking it; add an external rod lock or pilot-operated check valve for secure load holding. With the 570 mm stroke, use an external guide to prevent rod bending and premature seal wear from side loads. Mounting options include LB foot, FA/FB flange, CA/CB/CR clevis, TC/TCM1/TCM2 trunnion, or I/Y/F/U rod knuckles.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSI Series Standard Cylinder JSI32X570S FAQ
At 0.5 MPa it pushes 402 N and pulls 345 N; at 0.7 MPa it pushes 563 N and pulls 483 N. The theoretical maximum force is 82 kgf at 1.0 MPa. It uses a G1/8 port, an M10x1.25 rod thread, and operates at speeds between 30 and 800 mm/s.
The JSI is a JIS-standard profile cylinder engineered to be shorter and more compact than an ISO 15552 cylinder of the same 32 mm bore. It features a hard-anodized aluminum extruded barrel without external rods, saving space on tight machinery.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSI Series Standard Cylinder JSI32X570S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.