Airtac JSI Series Standard Cylinder JSI40X1500S
The AirTAC Airtac JSI Series Standard Cylinder JSI40X1500S is a genuine double acting JIS-standard air cylinder with a Ø40mm bore and 1500mm stroke, G1/4 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ40 mm
- Stroke1500 mm
- Port sizeG1/4
- Acting typeDouble acting
- Rod threadM14×1.5
- CushionAdjustable, 20.5 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSI Series Standard Cylinder JSI40X1500S
Generating 628 N of push force at 0.5 MPa, this double-acting 40 mm bore cylinder handles long 1500 mm reaches. Because it is a JIS-standard profile unit, it is shorter and more compact than an ISO 15552 cylinder of the same bore, saving valuable machine space. The extruded hard-anodized aluminum barrel omits external rods to resist wear, while the two-way piston seal retains grease for a long, low-friction service life.
Since 1500 mm exceeds the 1200 mm standard maximum for this bore, this is a non-standard, made-to-order stroke. The -S suffix means a piston magnet is built in, allowing CMSE or DMSE switches to drop directly into the side grooves for position sensing. Plan for roughly 377 N of real work at 0.5 MPa, which equates to lifting about 32 kg vertically with a 2:1 safety margin. The air port is G1/4.
Airtac JSI Series Standard Cylinder JSI40X1500S Technical Specifications
| Model | Airtac JSI Series Standard Cylinder JSI40X1500S |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 1500 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M14×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 20.5 mm |
| Max standard stroke | Up to 1200 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø40mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac JSI Series Standard Cylinder JSI40X1500S
| JSI | JIS-standard profile cylinder (double-acting type). |
|---|---|
| 40 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×1500 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSI Series Standard Cylinder JSI40X1500S Is Used
Extended-Reach Transfer
Pushes packages between distant conveyor sections on packaging lines, utilizing the full 1500 mm stroke to bridge wide machine gaps.
High-Bay Storage Pusher
Actuates a long-throw diverter arm in automated small-parts warehousing, moving totes with the 32 kg vertical lift capacity in mind.
Textile Beam Indexing
Shifts heavy fabric beams across a wide loom framework, where the compact JIS profile saves floor space and the G1/4 port delivers steady airflow.
Is the Airtac JSI Series Standard Cylinder JSI40X1500S the Right Cylinder?
For sizing context, a smaller JSI32 bore yields 402 N of push at 0.5 MPa, whereas stepping up to a JSI50 bore increases that to 982 N. When air is lost or the valve is centered, the piston will drift; the adjustable air cushions only decelerate the rod near the stroke ends and do not act as a brake. To hold a load securely, add an external rod lock or a pilot-operated check valve. The included -S magnet pairs perfectly with CMSE or DMSE sensors.
At 1500 mm, this non-standard stroke requires careful attention to side loads. Long extension distances increase the risk of rod bending, so mounting this unit with an external guide or linear rail is strongly recommended to prevent premature seal wear and binding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSI Series Standard Cylinder JSI40X1500S FAQ
At 0.5 MPa it provides 628 N push and 528 N pull. At 0.7 MPa it provides 879 N push and 739 N pull. The theoretical maximum force is 128 kgf at 1.0 MPa. It features a 40 mm bore, a 16 mm rod, an M14x1.5 rod thread, a G1/4 port, and adjustable air cushions of 20.5 mm at both ends.
The JSI is a JIS-standard profile cylinder, making it shorter and more compact than an ISO 15552 cylinder of the same 40 mm bore. It uses an extruded hard-anodized aluminum barrel without external rods. Because this specific unit has the -S suffix, it includes a magnet for CMSE or DMSE sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSI Series Standard Cylinder JSI40X1500S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.