This model is discontinued
AirTAC has phased out the MALJ series. You can still order this code here: we ship the direct replacement MBLJ32X200-20S, with the same bore, stroke, output force, port and mounting, so it fits the same application. The MBLJ replacement upgrades to a riveted rolling-packed body and CMSG / DMSG / EMSG sensors (the MAL used CS1-M / DS1-M).
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X200-20-S
The AirTAC Airtac MALJ32 Adjustable Mini Cylinder MALJ32X200-20-S is a double-acting aluminum mini cylinder with a rear adjustable-stroke stopper: you can trim up to 20 mm, giving a usable end-position window from 180 to 200 mm. This model is discontinued — the direct replacement is the MBLJ32X200-20-S.
- BoreØ32 mm
- Stroke200 mm
- Adjust window180–200 mm
- Port sizeG1/8
- Rod threadM10×1.25
- StatusDiscontinued → MBLJ32X200-20-S
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X200-20-S
The AirTAC MALJ32X200-20-S is a discontinued double-acting double-rod mini cylinder with a 32mm bore and 200mm stroke. The direct replacement is the MBLJ32X200-20-S, matching bore, stroke, force, G1/8 port, and mounting.
This adjustable-stroke unit features a fixed rubber bumper, not an adjustable air cushion. The rear adjuster sets the end position but is a travel stop, not a lock, meaning it cannot hold a load without live air. Upgrading to the MBLJ brings a riveted rolling-packed body instead of the MALJ threaded covers, and the -S magnet switches from the older CS1-M/DS1-M to the modern CMSG/DMSG/EMSG family.
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X200-20-S Technical Specifications
| Model | Airtac MALJ32 Adjustable Mini Cylinder MALJ32X200-20-S |
|---|---|
| Series | MALJ adjustable-stroke mini cylinder (discontinued) |
| Replacement | MBLJ32X200-20-S |
| Bore size | Ø32 mm |
| Stroke | 200 mm |
| Adjustable window | 180 – 200 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
The rear adjuster is a travel stop, not a lock — it sets the end position but does not hold the load without live air. No back-cover code and no SDB on adjustable-stroke. The MBLJ32X200-20-S carries the same ratings.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
MALJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod MAL push of the same bore. The MBLJ32X200-20-S matches these values.
Model Code: Airtac MALJ32 Adjustable Mini Cylinder MALJ32X200-20-S
| MALJ | Adjustable-stroke aluminum mini cylinder, double acting (discontinued). |
|---|---|
| 32 | Bore size in mm (20/25/32/40). |
| ×200 | Nominal stroke length in mm. |
| -20 | Adjustable amount: trim the end to a 180–200 mm window. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBLJ uses CMSG/DMSG/EMSG). |
Replacement: MALJ → MBLJ. No back-cover (CA/U/CM) and no SDB. Mounting: FA / LB.
Where the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X200-20-S Is Used
Carton Flap Tucking
Adjust the 20mm rear stop on a case packer to tuck varying carton flaps at high speed, relying on the fixed rubber bumper to soften end impact.
Textile Fabric Spreader
Fine-tune the 200mm reach on a fabric edge-guide without bolting external stops, ensuring the 346N pull retracts the guide roll smoothly.
Replacing the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X200-20-S with MBLJ32X200-20-S
To replace the MALJ32X200-20-S, order the direct replacement MBLJ32X200-20-S. Confirm the 32mm bore, 200mm stroke, 20mm adjust code, G1/8 PT port, and M10x1.25 rod thread. Mounting is FA or LB only (no back cover or SDB). The -S magnet requires new CMSG/DMSG/EMSG sensors. Remember the adjuster is a stop, not a lock.
At 200mm stroke, avoid side-load rod-bending by guiding the load properly.
Upgrade checklist
- ✓ Order the MBLJ32X200-20-S (same bore/stroke/adjust)
- ✓ Same 180–200 mm adjustable window
- ✓ Adjuster is a stop, not a lock
- ✓ No back cover / SDB — plan an FA/LB mount
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check The rear adjuster sets the end position — it is not a load lock.
- check No back-cover / SDB on adjustable-stroke — use FA / LB.
- check Front/rear covers are threaded — not for field disassembly.
- check For new builds, specify the MBLJ32X200-20-S instead of this discontinued model.
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X200-20-S FAQ
Yes, the MALJ32X200-20-S is discontinued. The direct replacement is the MBLJ32X200-20-S, matching the 32mm bore, 200mm stroke, 20mm adjuster, and G1/8 port. The MBLJ upgrades the body to a riveted rolling-packed design and uses CMSG/DMSG/EMSG sensors instead of the older CS1-M/DS1-M switches.
The 200mm stroke with a 20mm adjuster gives a usable window of 180-200mm. The adjuster is a travel stop, not a lock; it cannot hold a load without air pressure.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Direct Upgrade
The MBLJ32X200-20-S replaces this model 1:1.
Fast Dispatch
MBLJ replacements are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBLJ Replacements
Request a Quote (Airtac MALJ32 Adjustable Mini Cylinder MALJ32X200-20-S → MBLJ32X200-20-S)
Tell us the quantity and destination — we quote the direct MBLJ32X200-20-S replacement with price, stock and lead time, usually within 7-8 hours.