Airtac MICJ Adjustable Mini Cylinder MICJ16X225-30S
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X225-30S is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 225mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke225 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X225-30S
Trim the forward stop by up to 30 mm on site without swapping hardware using the AirTAC MICJ16X225-30S. This double-acting, ISO 6432 round-body stainless steel mini cylinder pairs that adjustable extend stroke with a needle-set air cushion at both ends, letting you dial in the 195-225 mm forward position while soaking up high-speed shock. The stainless barrel and Ø6 mm piston rod shrug off mild washdown and corrosion.
The -S suffix means a built-in piston magnet is present for CMSG, DMSG, or EMSG position sensing, and the M5×0.8 port keeps airflow compact for the 30-800 mm/s speed range.
Airtac MICJ Adjustable Mini Cylinder MICJ16X225-30S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X225-30S |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 225 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X225-30S
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×225 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X225-30S Is Used
Gauge Positioning
Dial in the 195-225 mm extend stop to seat a gauging probe against machined parts with 100.5 N of precise push force.
Light Press Fit
Use the dual adjustable air cushions to decelerate the Ø6 rod smoothly when pressing delicate bearings at up to 800 mm/s.
Parts Ejection
Rely on the CMSG sensor signal and 86.4 N retract pull to confirm ejection of lightweight plastic caps from a washdown-friendly stainless body.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X225-30S the Right Cylinder?
Choose this Ø16 bore when you need fast, settable-position moves under 60 N and want the shock absorption of a true air cushion. The external screw sets the extend end position only; it is not a mid-stroke lock, and the piston will drift on air loss. Use an external rod lock or pilot check valve to hold a suspended load.
Mounting follows the standard ISO 6432 mini interface via LB foot, FA flange, or TC trunnion brackets (the SDB pivot-block is not offered on this adjustable variant). Because this SKU includes the -S magnet, you can directly mount CMSG, DMSG, or EMSG sensors for end-of-stroke confirmation.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X225-30S FAQ
The external screw shortens the extend stroke by up to 30 mm, while the needle-set air cushions at both ends absorb high-speed impact. The -S suffix indicates a built-in magnet for CMSG, DMSG, or EMSG sensors; the cushion only decelerates near stroke end and does not lock the load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X225-30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.