
The AirTAC MICJ Adjustable Mini Cylinder MICJ40X500-75 is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø40mm bore and 500mm stroke, 1/4" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
Dial in a precise forward stop on-site without swapping hardware using the AirTAC MICJ40X500-75. An external screw shortens the extend stroke by up to 75 mm, yielding a usable 425-500 mm forward range, while a needle-set adjustable air cushion at both ends absorbs high-speed impact. As a double-acting, round-body stainless steel mini cylinder, the Ø40 mm bore pushes 628.3 N and pulls 527.8 N at 0.5 MPa.
Built with a stainless barrel and rod for mild washdown resistance, this unit runs on a 1/4" port with an M12x1.25 male rod thread. Note that Ø40 is a non-ISO-6432 size, and this specific SKU lacks a magnet, so it cannot host CMSG/DMSG/EMSG sensors.
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ40X500-75 |
|---|---|
| Series | MICJ mini cylinder |
| Bore size | Ø40 mm |
| Stroke | 500 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | 1/4" |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø40 bore is a larger, non-ISO-6432 size.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| MICJ | round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 40 | Bore size in mm. |
| ×500 | Stroke length in mm. |
| -75 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Execute light press operations where the 32 kg vertical lift capacity is sufficient, relying on the adjustable air cushion to soften the final impact.
Halt advancing pallets at a wrapping station, using the on-site extend adjustment to fine-tune the stopping distance for mixed load sizes.
When sizing this 40 mm bore, stepping down to a Ø32 mm MICJ drops the 0.5 MPa push force to 402.2 N, while no larger MICJ bore exists above 40 mm. The 75 mm extend adjuster paired with the dual air cushions is perfect for tuning fast, settable-position moves where you must precisely control the impact at the end of travel. Use LB foot, FA flange, or TC trunnion mounts, as the SDB pivot-block is not offered on adjustable-stroke variants.
Remember that the stop screw sets the end position but acts as no mid-stroke lock. The cylinder will drift on air loss, and the cushion only decelerates near the stroke end rather than holding the load. To suspend a load safely, integrate an external rod lock or pilot-operated check valve.
AirtacDistr lists every MICJ40 order code with its price on one page at https://airtacdistr.com/products/airtac-micj40-adjustable-double-rod-cushioned-mini-cylinder
Quick checklist
This double-acting cylinder features a 1/4" port and an M12x1.25 male rod thread.
The external screw shortens the extend stroke by up to 75 mm, while the needle-set air cushions at both ends decelerate the piston at high speed. The cushion only slows travel near the ends and does not lock the piston; the cylinder drifts on air loss, so use an external rod lock for holding. This SKU has no magnet and cannot take sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.