Airtac SAIF Series Standard Cylinder with Valve SAIF63X75-10A
The AirTAC Airtac SAIF Series Standard Cylinder with Valve SAIF63X75-10A is a genuine double-acting ISO 15552 cylinder with a Ø63mm bore, 75mm stroke and a built-in 4M310-10 5/2 solenoid valve — it switches itself from one coil signal, so no separate remote valve or extra plumbing is needed.
- BoreØ63 mm
- Stroke75 mm
- Built-in valve4M310-10
- Valve port3/8"
- CoilAC220V
- EntryTerminal
About the Airtac SAIF Series Standard Cylinder with Valve SAIF63X75-10A
The AirTAC SAIF63X75-10A is a double-acting ISO 15552 profile cylinder equipped with a built-in 4M310-10 5/2 solenoid valve. This integrated valve provides an effective flow area of 30.0 mm2 (Cv 1.68) and operates at a maximum frequency of 4 cycles per second. Driven by an AC220V terminal connection coil consuming 3.5 VA, it features IP65 protection and a rapid activation time of 0.05 seconds. The assembly switches itself from a single electrical signal, eliminating the need for remote plumbing. While the cylinder body rates to 1.0 MPa, the practical operating range for this valved unit is 0.15-0.8 MPa.
At 0.5 MPa, this 63mm bore generates 1559N of push force and 1402N of pull force, stepping up to 2182N push at 0.7 MPa. The manifold links the valve to the cylinder using PU tubing (O10 x O6.5). Factory set to retract the rod when the coil is energised, the valve can be repositioned to extend-when-energised if your logic requires it. The base cylinder is dimensionally interchangeable per ISO 15552 and features variable air cushions at both ends (30mm stroke length) to decelerate the load near stroke end.
Airtac SAIF Series Standard Cylinder with Valve SAIF63X75-10A Technical Specifications
| Model | Airtac SAIF Series Standard Cylinder with Valve SAIF63X75-10A |
|---|---|
| Series | SAIF ISO 15552 cylinder with valve |
| Bore size | Ø63 mm |
| Stroke | 75 mm |
| Acting type | Double acting, self-valved |
| Cylinder port | G3/8 |
| Rod thread | M16×1.5 |
| PU tube | Ø10 × Ø6.5 |
| Built-in valve | 4M310-10 (5/2) |
|---|---|
| Valve flow | 30.0 mm² (Cv 1.68) |
| Max frequency | 4 cycle/sec |
| Coil voltage | AC220V · AC 3.5 VA |
| Electrical entry | Terminal · IP65 · B class |
| Response time | 0.05 s and below |
| Operating pressure | 0.15 – 0.8 MPa (valve limit) |
| Speed range | 30 – 800 mm/s |
The cylinder rates to 1.0 MPa but the built-in valve operates 0.15–0.8 MPa, so run the assembled SAIF at 0.15–0.8 MPa. Default: rod retracts when the coil is energised (reconfigurable to extend). Specs follow the official AirTAC SAIF datasheet. Port options: PT / G.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
Sized within the valve's 0.15–0.8 MPa range. Actual usable force is lower than theoretical due to friction and back-pressure.
Model Code: Airtac SAIF Series Standard Cylinder with Valve SAIF63X75-10A
| SAIF | ISO 15552 cylinder with built-in 4M valve. |
|---|---|
| 63×75 | Bore × stroke in mm. |
| -10 | Valve port 3/8" → 4M310-10. |
| A | Coil voltage AC220V. |
| I / (blank) | Terminal electrical entry. |
SAIF does not hold its load without air — the valve routes air, it is not a lock. For load-holding use a SAIL (lock) or BSAI (clamp-lock).
Where the Airtac SAIF Series Standard Cylinder with Valve SAIF63X75-10A Is Used
Decentralized Machine Stations
Ideal for large machines where running remote valve tubing is costly, allowing each station to control its own actuation via a single AC220V signal.
Mid-Force Clamping
Provides 1559N of push force at 0.5 MPa for securely holding workpieces during machining, without needing a separate valve manifold.
Space-Constrained Retrofits
The integrated 4M310 valve and manifold block save valuable panel and footprint space when upgrading existing pneumatic setups.
Is the Airtac SAIF Series Standard Cylinder with Valve SAIF63X75-10A the Right Choice?
Choose this 63mm bore when a 50mm bore (982N push at 0.5 MPa) is insufficient, or step down if a 50mm provides enough force. A self-valved SAIF is ideal for decentralized stations across large machines, saving panel space and reducing tubing runs compared to a separate cylinder and remote valve. For this specific model, verify your coil voltage is AC220V with a terminal entry, the valve port is 3/8 inch, and the cylinder port is PT3/8. Note that neither the 5/2 valve nor the air cushions lock or hold the load without live pressure; for true position holding, consider the SAIL lock or BSAI clamp-lock series. Replacement requires matching the 63mm bore, 75mm stroke, 4M310-10 valve, AC220V terminal coil, PT thread, and no magnet (-S).
Quick checklist
- ✓ Force at 0.15–0.8 MPa
- ✓ Coil voltage matches panel
- ✓ Terminal vs grommet entry
- ✓ Retract- or extend-when-energised
- ✓ Load-holding → SAIL / BSAI
Airtac SAIF Series Standard Cylinder with Valve SAIF63X75-10A FAQ
The 63mm bore provides 1559N push and 1402N pull force at 0.5 MPa. The built-in 4M310-10 valve has an effective area of 30.0 mm2 (Cv 1.68) and supports up to 4 cycles per second.
No, the SAIF controls itself from one AC220V coil signal, making it perfect for decentralized installations. Factory set to retract when energised, the 5/2 valve can be repositioned to extend-when-energised if needed.
Request a Quote for Airtac SAIF Series Standard Cylinder with Valve SAIF63X75-10A
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.