
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X85-40 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 85mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X85-40 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster. The integrated rear stopper allows you to trim the effective travel, providing a usable stroke window of 45 to 85mm for precise positioning at commissioning.
This adjustable-stroke design eliminates the need to swap out an entire cylinder or add bulky external stops when fine-tuning machine end-positions. It features a reduced mounting subset of Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR options. The extruded aluminum barrel includes sensor grooves on both sides, ready for CMSE reed or DMSE electronic sensors if a magnet is added later.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X85-40 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 85 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×85 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the retract distance from 45 to 85mm during product size transitions without replacing the cylinder or bolting on external stops.
Fine-tune the final resting position at commissioning to compensate for mechanical wear or sensor placement variations.
Establish precise, repeatable stroke endpoints for delicate operations that require adjustable mechanical limits.
If your process needs less force, stepping down to a 32mm bore yields 402N; if you require significantly higher clamping power, the 63mm bore provides 1559N. The SAIJ40X85-40 is selected specifically over a fixed-stroke SAI model when you need live in-field tuning of the retract position.
Remember that the rear adjuster acts only as a travel stop, not a lock; it cannot hold a load without continuous live air pressure. For load-holding requirements without air, consider an external pilot-operated check valve, or specify a SAIL or BSAI cylinder. To match this ISO 15552 footprint exactly, ensure your replacement parameters match the 40mm bore, 85mm nominal stroke, 40mm adjustment range, PT G1/4 port, and the specified mounting set.
Quick checklist
The rear adjusting screw allows you to shorten the effective travel by up to 40mm. This creates a usable stroke window of 45 to 85mm, letting you set the exact retract end-position during setup without changing the cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.