Airtac SAIJ80 Adjustable Cylinder SAIJ80BX750-10
The AirTAC SAIJ80 Adjustable Cylinder SAIJ80BX750-10 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø80mm bore and 750mm stroke, G3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ80 mm
- Stroke750 mm
- Port sizeG3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SAIJ80 Adjustable Cylinder SAIJ80BX750-10
The AirTAC SAIJ80X750-10 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that allows you to fine-tune the retract end position. With a nominal 750 mm stroke and a 10 mm adjustment screw, it provides a usable travel window of 740-750 mm, letting you dial in the exact end-stop at commissioning without adding external stops.
This variant uses a SUS304 stainless steel rod for corrosion resistance and a PT tapered port thread. It carries the standard SAIJ mounting subset of Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR options. The rear adjuster acts strictly as a travel stop and does not hold the load without live air pressure.
Airtac SAIJ80 Adjustable Cylinder SAIJ80BX750-10 Technical Specifications
| Model | Airtac SAIJ80 Adjustable Cylinder SAIJ80BX750-10 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 750 mm |
| Acting type | Double acting |
| Port size | G3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | — |
| Max (@1.0 MPa) | 463 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SAIJ80 Adjustable Cylinder SAIJ80BX750-10
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×750 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SAIJ80 Adjustable Cylinder SAIJ80BX750-10 Is Used
Product Changeover
Dial in the 740-750 mm end-stop during line changeovers to accommodate different product lengths without replacing the cylinder.
Machine Setup
Fine-tune the retract position during initial machine build, eliminating the need to bolt on external physical stops.
Is the Airtac SAIJ80 Adjustable Cylinder SAIJ80BX750-10 the Right Cylinder?
The adjustable stroke is ideal for machine setup and product changeover, allowing variable end-stops without swapping the cylinder. For strokes of 750 mm, the 25 mm rod diameter handles high side loads, but an external guide is recommended to prevent rod bending.
Because the rear adjuster only sets the travel end and the air cushions manage deceleration, this cylinder will not hold a load without live air. For load-holding without pressure, consider the SAIL (air-released lock) or BSAI (clamp-lock) series. This model is dimensionally interchangeable per ISO 15552 mounting interfaces.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SAIJ80 Adjustable Cylinder SAIJ80BX750-10 FAQ
The rear adjuster screw allows you to shorten the effective travel from the 750 mm nominal stroke down to 740 mm, giving a 740-750 mm usable window. It acts as a mechanical stop to fine-tune the end position and does not lock the load without live air pressure.
At 0.9 MPa, the push force increases to 4523 N.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SAIJ80 Adjustable Cylinder SAIJ80BX750-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.