Airtac SCJ32 Standard Cylinder SCJ32X130-20
The AirTAC Airtac SCJ32 Standard Cylinder SCJ32X130-20 is a genuine double-acting SINGLE-ROD air cylinder with a rear-cap ADJUSTING SCREW: the stroke end is field-adjustable within a 20 mm range without swapping the cylinder. Ø32mm bore, 130mm nominal stroke, PT1/8 ports and adjustable end cushioning.
- BoreØ32 mm
- Nominal stroke130 mm
- Stroke adjust-20 mm
- Port sizePT1/8
- Rod threadM10×1.25
- CushionAdjustable, 21 mm
About the Airtac SCJ32 Standard Cylinder SCJ32X130-20
The SCJ32X130-20 is a double-acting, single-rod pneumatic cylinder with a rear adjusting screw that lets you shorten the effective stroke by up to 20 mm in the field. At 0.5 MPa it delivers 402 N push and 345 N pull, making it a practical actuator for light clamping, sorting, or diverting tasks where the end position needs occasional tweaking.
This 32 mm bore model uses a 12 mm rod, PT1/8 ports, and an M10x1.25 rod thread. The body length A(SCJ) is 182 mm, and the adjustable air cushion helps decelerate the piston smoothly. The cylinder is rated for 0.15–1.0 MPa and speeds of 30–800 mm/s, with a maximum standard stroke of 1000 mm for this bore.
Airtac SCJ32 Standard Cylinder SCJ32X130-20 Technical Specifications
| Model | Airtac SCJ32 Standard Cylinder SCJ32X130-20 |
|---|---|
| Series | SCJ adjustable-stroke tie-rod cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 130 mm |
| Stroke adjustment | Up to 20 mm (rear adjusting screw) |
| Acting type | Double acting (single rod) |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 21 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SCJ (adjustable-stroke) datasheet. The rear adjusting screw sets the stroke end position; force is the same as the equivalent single-rod SC bore. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
SCJ is single-rod, so force matches the equivalent SC bore: push uses the full bore area, pull subtracts the rod area. Actual usable force is lower than theoretical due to friction and back-pressure; size with a safety margin.
Model Code: Airtac SCJ32 Standard Cylinder SCJ32X130-20
| SCJ | Adjustable-stroke tie-rod cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×130 | Nominal (maximum) stroke length in mm. |
| -20 | Adjustable-stroke range in mm (options 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for sensor position sensing. |
Related types: SC (single rod, fixed stroke), SCD (double rod), SCT (multi-position). SCJ mounting: Basic, FA, LB, TC, TCM1. Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SCJ32 Standard Cylinder SCJ32X130-20 Is Used
Commissioning Fine-Tuning
During machine setup, technicians can dial in the exact retract stop position with the rear screw, eliminating the need to fabricate shims or swap cylinders.
Small-Part Diverting
Adjust the stroke end to match different lane widths on a conveyor. The 20 mm range handles product changeovers without mechanical rework.
Wear Take-Up on Clamps
As gripper pads or clamp faces wear down, the adjusting screw can be turned to restore the original clamping position, extending maintenance intervals.
Is the Airtac SCJ32 Standard Cylinder SCJ32X130-20 the Right Cylinder?
Choose the SCJ32 when you need a compact adjustable-stroke cylinder in the 402 N push class. If the load demands more force, step up to the 40 mm bore (628 N push at 0.5 MPa). For applications that don't require stroke adjustment, the fixed-stroke SC32 is a simpler, cost-effective alternative. A direct replacement must match the 32 mm bore, 130 mm nominal stroke, 20 mm adjust range, PT ports, and basic mounting. At 130 mm stroke, rod deflection is minimal, but for any side-loading use an external guide rail.
Adjustable-stroke checklist
- ✓ Need to fine-tune stroke on the line?
- ✓ Nominal stroke + adjust range (-20)
- ✓ Required force at your working pressure
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Set the rear adjusting screw, then lock it before running.
- check Adjust end cushion screws for smooth stops.
- check Use SCJ mounting accessory (FA / LB / TC / TCM1).
- check Installation by qualified personnel per AirTAC docs.
Airtac SCJ32 Standard Cylinder SCJ32X130-20 FAQ
At 0.5 MPa, it provides 402 N pushing and 345 N pulling (the pull force is lower because of the single 12 mm rod). At the maximum operating pressure of 0.9 MPa, the push force reaches 724 N.
Only if you need the adjustable stroke feature. The SCJ32X130-20 is slightly longer than the fixed-stroke SC32 and adds a rear screw. It matches the same bore, port, and rod dimensions, but ensure the extra length and the 20 mm adjustment range fit your machine envelope.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SCJ Adjustable-Stroke Cylinders
Request a Quote for Airtac SCJ32 Standard Cylinder SCJ32X130-20
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.