Airtac SCJ32 Standard Cylinder SCJ32X300-30S
The AirTAC Airtac SCJ32 Standard Cylinder SCJ32X300-30S is a genuine double-acting SINGLE-ROD air cylinder with a rear-cap ADJUSTING SCREW: the stroke end is field-adjustable within a 30 mm range without swapping the cylinder. Ø32mm bore, 300mm nominal stroke, PT1/8 ports and adjustable end cushioning.
- BoreØ32 mm
- Nominal stroke300 mm
- Stroke adjust-30 mm
- Port sizePT1/8
- Rod threadM10×1.25
- CushionAdjustable, 21 mm
About the Airtac SCJ32 Standard Cylinder SCJ32X300-30S
The SCJ32X300-30S is a double-acting, single-rod tie-rod cylinder with a rear-cap adjusting screw that provides 30 mm of field-adjustable stroke-end control, letting you fine-tune the 300 mm nominal stroke without removing the cylinder. At 0.5 MPa it delivers 402 N push and 345 N pull, driven by a 12 mm diameter rod through PT1/8 ports.
A built-in magnet (the -S suffix) allows CMSG/DMSG/EMSG reed or solid-state sensors to clamp directly onto the barrel for non-contact position sensing. The 21 mm air cushion at each end decelerates the piston smoothly, and the TPU seal keeps the unit running from -20 to +70 °C with standard filtered air.
Airtac SCJ32 Standard Cylinder SCJ32X300-30S Technical Specifications
| Model | Airtac SCJ32 Standard Cylinder SCJ32X300-30S |
|---|---|
| Series | SCJ adjustable-stroke tie-rod cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 300 mm |
| Stroke adjustment | Up to 30 mm (rear adjusting screw) |
| Acting type | Double acting (single rod) |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 21 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SCJ (adjustable-stroke) datasheet. The rear adjusting screw sets the stroke end position; force is the same as the equivalent single-rod SC bore. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
SCJ is single-rod, so force matches the equivalent SC bore: push uses the full bore area, pull subtracts the rod area. Actual usable force is lower than theoretical due to friction and back-pressure; size with a safety margin.
Model Code: Airtac SCJ32 Standard Cylinder SCJ32X300-30S
| SCJ | Adjustable-stroke tie-rod cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×300 | Nominal (maximum) stroke length in mm. |
| -30 | Adjustable-stroke range in mm (options 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for sensor position sensing. |
Related types: SC (single rod, fixed stroke), SCD (double rod), SCT (multi-position). SCJ mounting: Basic, FA, LB, TC, TCM1. Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SCJ32 Standard Cylinder SCJ32X300-30S Is Used
Commissioning & Setup Trials
The 30 mm adjust range lets commissioning engineers dial in the exact stroke end on a new assembly fixture without swapping cylinders or machining hard stops, saving hours during line bring-up.
Small-Part Sorting Gates
Use the adjustable stroke to set the gate opening precisely for different component sizes on a conveyor; the built-in magnet confirms gate position at every cycle via a CMSG sensor.
Wear Take-Up on Clamping Jigs
As clamp pads wear, the rear screw can advance the stroke end by up to 30 mm to restore full clamping force without replacing the cylinder, keeping a 32 mm bore pneumatic clamp in service longer.
Is the Airtac SCJ32 Standard Cylinder SCJ32X300-30S the Right Cylinder?
Step up to the 40 mm bore SCJ40X300-30 for 628 N push at 0.5 MPa if the 402 N of this 32 mm model is marginal, or drop to a fixed-stroke SC32X300 when the application never needs stroke adjustment. For a direct replacement, match the 32 mm bore, 300 mm nominal stroke, 30 mm adjust range, PT port thread, basic mount, and the -S magnet option—any deviation in the adjust code or sensor readiness will change the cylinder’s tuning envelope. At 300 mm of stroke, ensure the rod is guided externally or switch to a guided cylinder if side loads are present, because the 12 mm rod can buckle under off-axis forces.
Adjustable-stroke checklist
- ✓ Need to fine-tune stroke on the line?
- ✓ Nominal stroke + adjust range (-30)
- ✓ Required force at your working pressure
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Set the rear adjusting screw, then lock it before running.
- check Adjust end cushion screws for smooth stops.
- check Use SCJ mounting accessory (FA / LB / TC / TCM1).
- check Installation by qualified personnel per AirTAC docs.
Airtac SCJ32 Standard Cylinder SCJ32X300-30S FAQ
At the standard 0.5 MPa operating pressure, push force is 402 N and pull force is 345 N. At the maximum operating pressure of 0.9 MPa, push force reaches 724 N. The pull force is lower because the 12 mm rod reduces the effective piston area on the return stroke.
Yes, if the original is an AirTAC SCJ32 with a 300 mm nominal stroke, a 30 mm adjust range, PT ports, basic mounting, and a magnet for sensors. The adjustable-stroke design is specific to the SCJ family—a fixed-stroke SC cylinder cannot be substituted without losing the field-adjustment feature.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SCJ Adjustable-Stroke Cylinders
Request a Quote for Airtac SCJ32 Standard Cylinder SCJ32X300-30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.