Airtac SCJ32 Standard Cylinder SCJ32X35-30
The AirTAC Airtac SCJ32 Standard Cylinder SCJ32X35-30 is a genuine double-acting SINGLE-ROD air cylinder with a rear-cap ADJUSTING SCREW: the stroke end is field-adjustable within a 30 mm range without swapping the cylinder. Ø32mm bore, 35mm nominal stroke, PT1/8 ports and adjustable end cushioning.
- BoreØ32 mm
- Nominal stroke35 mm
- Stroke adjust-30 mm
- Port sizePT1/8
- Rod threadM10×1.25
- CushionAdjustable, 21 mm
About the Airtac SCJ32 Standard Cylinder SCJ32X35-30
The SCJ32X35-30 is a double-acting, single-rod pneumatic cylinder with a field-adjustable stroke, allowing the rear stop position to be fine-tuned by up to 30 mm without removing the unit. With a 32 mm bore delivering 402 N of push force at 0.5 MPa and a compact body length A of 182 mm, it suits light automation tasks where commissioning or format changes demand flexible end-position setting.
This model uses a 12 mm diameter piston rod with an M10x1.25 thread and PT1/8 ports. The integrated air cushion (21 mm) ensures quiet deceleration, while the tie-rod construction provides robust service. The adjustable screw sets only the stroke end, not the force or speed, making it a precise mechanical stop for repetitive positioning.
Airtac SCJ32 Standard Cylinder SCJ32X35-30 Technical Specifications
| Model | Airtac SCJ32 Standard Cylinder SCJ32X35-30 |
|---|---|
| Series | SCJ adjustable-stroke tie-rod cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 35 mm |
| Stroke adjustment | Up to 30 mm (rear adjusting screw) |
| Acting type | Double acting (single rod) |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 21 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SCJ (adjustable-stroke) datasheet. The rear adjusting screw sets the stroke end position; force is the same as the equivalent single-rod SC bore. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
SCJ is single-rod, so force matches the equivalent SC bore: push uses the full bore area, pull subtracts the rod area. Actual usable force is lower than theoretical due to friction and back-pressure; size with a safety margin.
Model Code: Airtac SCJ32 Standard Cylinder SCJ32X35-30
| SCJ | Adjustable-stroke tie-rod cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×35 | Nominal (maximum) stroke length in mm. |
| -30 | Adjustable-stroke range in mm (options 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for sensor position sensing. |
Related types: SC (single rod, fixed stroke), SCD (double rod), SCT (multi-position). SCJ mounting: Basic, FA, LB, TC, TCM1. Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SCJ32 Standard Cylinder SCJ32X35-30 Is Used
Commissioning & Setup
Ideal for machine builders who need to fine-tune the actuator end-stop during initial system bring-up, eliminating the need to swap cylinders or fabricate custom hard stops.
Wear Compensation
In clamping or pressing fixtures, the 30 mm adjustment range allows operators to take up slack from pad wear or workpiece variation, maintaining consistent clamping force over time.
Small Part Sorting
Used on diverter gates for small conveyors, where the adjustable stroke lets a single cylinder model handle multiple product widths by simply turning the rear screw.
Is the Airtac SCJ32 Standard Cylinder SCJ32X35-30 the Right Cylinder?
Choose the SCJ32X35-30 when you need to dial in a precise stroke end within a 30 mm window. If the 402 N push force at 0.5 MPa is insufficient, stepping up to the 40 mm bore provides 628 N. For applications where the stroke is permanently fixed and never needs field adjustment, the standard SC32 fixed-stroke cylinder is a simpler, cost-effective alternative. A direct replacement must match the 32 mm bore, 35 mm nominal stroke, 30 mm adjustable range, PT ports, and basic mounting.
Adjustable-stroke checklist
- ✓ Need to fine-tune stroke on the line?
- ✓ Nominal stroke + adjust range (-30)
- ✓ Required force at your working pressure
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Set the rear adjusting screw, then lock it before running.
- check Adjust end cushion screws for smooth stops.
- check Use SCJ mounting accessory (FA / LB / TC / TCM1).
- check Installation by qualified personnel per AirTAC docs.
Airtac SCJ32 Standard Cylinder SCJ32X35-30 FAQ
At 0.5 MPa, the push force is 402 N and the pull force is 345 N due to the single rod reducing the piston area on the return side. The maximum operating push force at 0.9 MPa is 724 N.
Physically, yes, as it shares the same bore and mounting footprint. However, the SCJ body is slightly longer to house the adjusting screw. Ensure the 30 mm adjustment range covers your stroke requirement and that the rear screw mechanism has clearance in your installation.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SCJ Adjustable-Stroke Cylinders
Request a Quote for Airtac SCJ32 Standard Cylinder SCJ32X35-30
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.