Airtac SCJ32 Standard Cylinder SCJ32X60-10S
The AirTAC Airtac SCJ32 Standard Cylinder SCJ32X60-10S is a genuine double-acting SINGLE-ROD air cylinder with a rear-cap ADJUSTING SCREW: the stroke end is field-adjustable within a 10 mm range without swapping the cylinder. Ø32mm bore, 60mm nominal stroke, PT1/8 ports and adjustable end cushioning.
- BoreØ32 mm
- Nominal stroke60 mm
- Stroke adjust-10 mm
- Port sizePT1/8
- Rod threadM10×1.25
- CushionAdjustable, 21 mm
About the Airtac SCJ32 Standard Cylinder SCJ32X60-10S
The SCJ32X60-10S is a double-acting, single-rod pneumatic cylinder that puts fine stroke tuning directly into your hands. Its rear-cap adjusting screw lets you shorten the stroke end by up to 10 mm on the machine, making it ideal for commissioning trials or taking up wear on compact fixtures. With a 12 mm rod diameter and M10x1.25 rod thread, this 32 mm bore unit delivers 402 N of push force at 0.5 MPa, scaling up to 724 N at 0.9 MPa.
This model includes a built-in magnet, so you can clamp CMSG, DMSG, or EMSG sensors directly onto the tie-rod barrel for reliable, non-contact position sensing. The body length A(SCJ) is 182 mm, and the cylinder handles a 60 mm nominal stroke with an operating pressure range of 0.15–1.0 MPa. Standard PT ports and TPU seals keep it ready for general industrial air service from -20 to +70 °C.
Airtac SCJ32 Standard Cylinder SCJ32X60-10S Technical Specifications
| Model | Airtac SCJ32 Standard Cylinder SCJ32X60-10S |
|---|---|
| Series | SCJ adjustable-stroke tie-rod cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 60 mm |
| Stroke adjustment | Up to 10 mm (rear adjusting screw) |
| Acting type | Double acting (single rod) |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 21 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SCJ (adjustable-stroke) datasheet. The rear adjusting screw sets the stroke end position; force is the same as the equivalent single-rod SC bore. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
SCJ is single-rod, so force matches the equivalent SC bore: push uses the full bore area, pull subtracts the rod area. Actual usable force is lower than theoretical due to friction and back-pressure; size with a safety margin.
Model Code: Airtac SCJ32 Standard Cylinder SCJ32X60-10S
| SCJ | Adjustable-stroke tie-rod cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×60 | Nominal (maximum) stroke length in mm. |
| -10 | Adjustable-stroke range in mm (options 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for sensor position sensing. |
Related types: SC (single rod, fixed stroke), SCD (double rod), SCT (multi-position). SCJ mounting: Basic, FA, LB, TC, TCM1. Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SCJ32 Standard Cylinder SCJ32X60-10S Is Used
Commissioning & Setup
Field-adjust the stroke end by up to 10 mm to dial in the exact actuator travel on new automation cells without swapping cylinders or machining stop blocks.
Wear Compensation
On clamping or pressing fixtures, the adjusting screw lets operators quickly take up mechanical play or pad wear, restoring precise end-position repeatability.
Small-Part Sorting Gates
Use the adjustable stroke to fine-tune the opening of a diverter gate on a compact conveyor, and confirm position via the built-in magnet and a DMSG sensor.
Is the Airtac SCJ32 Standard Cylinder SCJ32X60-10S the Right Cylinder?
Step up to the 40 mm bore SCJ for 628 N of push force at 0.5 MPa if your load is marginal, or step down to a fixed-stroke SC32 if you never need to alter the end position. The SCJ is the right choice when you expect to fine-tune the stroke during setup or after mechanical wear, without adding external hard stops. For a direct replacement, match the 32 mm bore, 60 mm nominal stroke, 10 mm adjust range, PT port thread, and the built-in magnet; basic mounting means no additional bracket is needed. If your application involves significant side loads, consider adding an external guide rail or switching to a guided cylinder assembly.
Adjustable-stroke checklist
- ✓ Need to fine-tune stroke on the line?
- ✓ Nominal stroke + adjust range (-10)
- ✓ Required force at your working pressure
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Set the rear adjusting screw, then lock it before running.
- check Adjust end cushion screws for smooth stops.
- check Use SCJ mounting accessory (FA / LB / TC / TCM1).
- check Installation by qualified personnel per AirTAC docs.
Airtac SCJ32 Standard Cylinder SCJ32X60-10S FAQ
At 0.5 MPa, it generates 402 N pushing and 345 N pulling (the difference is due to the single rod). At the maximum operating pressure of 1.0 MPa, the theoretical push force reaches 804 N, but the rated maximum is 0.9 MPa, producing 724 N of push force.
Yes, if you need the 10 mm field-adjustable stroke feature. The SCJ shares the same 32 mm bore, double-acting single-rod design, and mounting accessories as the SC series. Ensure you match the 60 mm nominal stroke, PT ports, and the magnet option if your existing setup uses sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SCJ Adjustable-Stroke Cylinders
Request a Quote for Airtac SCJ32 Standard Cylinder SCJ32X60-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.