Airtac SE32 Standard Cylinder SE32BX300SH
The AirTAC SE32 Standard Cylinder SE32BX300SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 300mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ32 mm
- Stroke300 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE32 Standard Cylinder SE32BX300SH
The AirTAC SE32BX300SH is a double-acting single-rod profile cylinder built to the ISO 15552 standard. It features a 32 mm bore and a 300 mm stroke, generating 402 N of push force at 0.5 MPa. Equipped with a SUS304 stainless steel rod and FKM seals, this unit operates reliably in high-temperature environments up to 150 C and corrosive washdown settings.
The extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush against machine frames. Integrated sensor grooves on three sides accept CMSE reed or DMSE electronic switches, enabled here by the built-in magnet for precise end-of-stroke detection.
Airtac SE32 Standard Cylinder SE32BX300SH Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32BX300SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 300 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32BX300SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×300 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32BX300SH Is Used
Lab Diagnostic Ejector
Uses the 402 N extend force and SUS304 rod to push tested vial racks out of a heated chemical centrifuge, resisting moisture and thermal stress.
Pouch Sealing Press
Cycles the 300 mm stroke to lower a heat bar onto medical film pouches, leveraging the FKM seal to withstand constant 150 C ambient radiant heat.
PCB Straightening Stop
Acts as a hard stop for warped circuit boards entering a reflow oven, relying on the adjustable end cushions to prevent impact damage to delicate traces.
Is the Airtac SE32 Standard Cylinder SE32BX300SH the Right Cylinder?
This 32 mm bore provides 402 N push at 0.5 MPa. If your application requires less force, a smaller option is not available below 32 mm in this series, but if you need more power, stepping up to the 40 mm bore yields 628 N push. Because this model carries a 300 mm stroke, the unsupported rod length increases bending moments on the front bearing under heavy lateral loads; an external guide rail should be used to prevent premature wear. It serves as a direct dimensional direct for any standard ISO 15552 cylinder, matching the PT1/8 port and standard mounting accessories.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32BX300SH FAQ
At 0.5 MPa it provides 402 N push and 345 N pull. At 0.7 MPa the push increases to 563 N, with a maximum push capacity of 82 kgf at 1.0 MPa. The operating speed ranges from 30-800 mm/s.
No, the adjustable air cushions at both ends only decelerate the piston near the stroke limits; they do not act as a braking mechanism. If the pneumatic supply is lost, the rod will drift, and an external rod lock or pilot-operated check valve is required to hold a load safely.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32BX300SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.