Airtac SE32 Standard Cylinder SE32X110
The AirTAC Airtac SE32 Standard Cylinder SE32X110 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 110mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke110 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X110
The AirTAC SE32X110 is a double-acting single-rod ISO 15552 profile cylinder, delivering a 402 N push force at 0.5 MPa from its 32 mm bore. Its square extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush on conveyors and small jigs while resisting edge corrosion.
This unit features field-adjustable pneumatic cushioning at both stroke ends, letting technicians tune the needle valve to soften hard end-stops at operating speeds up to 800 mm/s. As this SKU lacks the -S magnet, it does not support CMSE or DMSE position sensing out of the box.
Airtac SE32 Standard Cylinder SE32X110 Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X110 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 110 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X110
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×110 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X110 Is Used
PCB Depaneling Router
Provides the 402 N extend force needed to push unpopulated circuit boards through a routing bit, utilizing the 110 mm stroke to clear fixture pins.
Carton Flap Folder
Drives small tucking blades on a case erector, where the compact 32 mm profile barrel fits between narrow conveyor side rails.
Lab Centrifuge Gate
Actuates a safety access cover on a clinical centrifuge, using the 27 mm cushion length to gently decelerate the 12 mm rod before the end cap.
Is the Airtac SE32 Standard Cylinder SE32X110 the Right Cylinder?
If 402 N of push is insufficient, step up to the 40 mm bore yielding 628 N at 0.5 MPa; if your load is lighter, drop to the 25 mm bore (noting AirTAC's ISO line starts at 32 mm, so consider the SMI series for smaller). Remember that a plain SE cylinder drifts when air is lost—the adjustable cushion only decelerates near stroke end and acts as no brake or load-holding device. For mid-stroke stops, add an external pilot-operated check valve or pivot to the BSE rod-lock variant. Because the 110 mm stroke is under 300 mm, the 12 mm rod handles normal side loads without requiring an external guide.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X110 FAQ
At 0.5 MPa, the 32 mm bore generates 402 N of push and 345 N of pull. At 0.7 MPa, push increases to 563 N, with a maximum push of 82 kgf at 1.0 MPa. The rod end thread is M10x1.25, and the air port is PT1/8.
Yes, the SE32X110 is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can use existing mounting hardware and drop it into the same footprint as other ISO 15552 profile cylinders without modifying the machine plate.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X110
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.