Airtac SE32 Standard Cylinder SE32X530S
The AirTAC Airtac SE32 Standard Cylinder SE32X530S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 530mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke530 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X530S
The AirTAC SE32X530S is a double-acting, single-rod ISO 15552 profile cylinder delivering 402 N of push force at 0.5 MPa. Its extruded aluminum barrel design omits external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion. The built-in magnet enables seamless position tracking using CMSE reed or DMSE electronic sensors.
Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts when cycling at speeds up to 800 mm/s. Because the 530 mm stroke exceeds the unsupported length where a 12 mm rod could deflect under lateral stress, pairing this unit with an external guide rail is strongly recommended to prevent premature bearing wear.
Airtac SE32 Standard Cylinder SE32X530S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X530S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 530 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X530S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×530 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X530S Is Used
Flow Wrapper End-Of-Stroke Dwell
Drives the sealing jaw carriage on a continuous motion flow wrapper, utilizing the 530 mm stroke to clear the web path for film loading while the CMSE sensor confirms retraction.
Diverter Gate Actuation
Pivots a reject diverter arm on a modular plastic belt conveyor, applying 402 N of push force at 0.5 MPa to physically redirect underweight packages off the line.
Sample Tray Extraction
Extends a linear sample tray from an environmental test chamber, relying on the adjustable cushion to bring the 12 mm rod to a smooth halt without jarring delicate specimens.
Is the Airtac SE32 Standard Cylinder SE32X530S the Right Cylinder?
Stepping down to the smaller SE25 bore is not an option in this ISO 15552 series, but moving up to the SE40 bore increases your 0.5 MPa push force to 628 N if your payload demands greater thrust. Keep in mind that a standard SE cylinder cannot hold a load if air pressure drops or the valve centers; the piston will drift, so apply a BSE rod lock for strict position holding. As a dimensionally interchangeable ISO 15552 component, this 32 mm bore, 530 mm stroke, PT1/8 ported cylinder serves as a direct drop-in replacement for equivalent profile cylinders, utilizing standard mounting accessories alongside its -S magnet configuration.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X530S FAQ
The SE32X530S generates 402 N push and 345 N pull at 0.5 MPa, 563 N push at 0.7 MPa, and a maximum push of 82 kgf at 1.0 MPa. It features a PT1/8 port and a 12 mm rod with an M10x1.25 thread.
Yes, the SE32X530S shares standardized ISO 15552 mounting interface dimensions, making it dimensionally interchangeable with other profile cylinders in the same bore class. You can reuse existing mounting brackets and pivot pins without machining new holes.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X530S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.