Airtac SE32 Standard Cylinder SE32X565S
The AirTAC Airtac SE32 Standard Cylinder SE32X565S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 565mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke565 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X565S
The AirTAC SE32X565S is a double-acting single-rod ISO 15552 profile cylinder engineered for a 32mm bore and a 565mm non-standard stroke. It delivers a 402N push force at 0.5 MPa and integrates a built-in magnet for position sensing. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush in tight machine envelopes.
Field-adjustable air cushioning at both ends allows you to tune end-of-stroke deceleration via a set screw, softening hard impacts when cycling at speeds up to 800 mm/s. Because this specific 565mm stroke exceeds the standard 1000mm maximum for this bore, it is manufactured as a made-to-order item, ensuring you get the exact travel required without compromising the 27mm cushion length or PT1/8 porting.
Airtac SE32 Standard Cylinder SE32X565S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X565S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 565 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X565S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×565 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X565S Is Used
PCB Depaneling Router
Drives the Z-axis cutting head of a router separating printed circuit boards, using the 565mm stroke to clear tall board arrays while the 402N push force maintains steady feed.
Package Diverter Arm
Actuates a sorting pop-up arm on a logistics conveyor, where the 32mm bore fits within tight side-frame clearances and the -S magnet triggers DMSE sensors to confirm package redirect.
Lab Sample Dispenser
Moves a fluid dispensing nozzle across testing stations, relying on the smooth adjustable cushioning to prevent sudden stops from splashing reagents during 800 mm/s cycles.
Is the Airtac SE32 Standard Cylinder SE32X565S the Right Cylinder?
When sizing this actuator, compare its 402N push at 0.5 MPa against your actual load. If you need less force, there is no smaller standard ISO 15552 bore in the SE series, so you would step up to the 40mm bore (628N push) for heavier payloads or faster cycle times. For long 565mm strokes on a 12mm rod, the unsupported piston is highly susceptible to side-load bending and rod-bearing wear; always pair this cylinder with an external linear guide to prevent premature seal failure.
As a standard ISO 15552 profile cylinder, it serves as a drop-in dimensional replacement for other ISO 15552 cylinders, sharing standard mounting hardware. To complete your setup, specify the PT1/8 port, your preferred mounting accessory (like LB foot or FA front flange), and CMSE reed or DMSE electronic sensors to leverage the installed -S magnet. Remember that the adjustable air cushion only decelerates the piston near the stroke end; it does not hold a load if air pressure is lost.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X565S FAQ
This 32mm bore cylinder provides a push force of 402N and a pull force of 345N at 0.5 MPa. At 0.7 MPa, the push force is 563N, with a maximum push of 82 kgf at 1.0 MPa. The 565mm stroke is a non-standard, made-to-order length that exceeds the standard 1000mm maximum catalog stroke for this bore.
Yes, the SE32X565S is dimensionally interchangeable per ISO 15552, serving as a drop-in replacement for other ISO 15552 profile cylinders. Note that it is double-acting and relies on live air pressure; the adjustable air cushion only decelerates the piston near the end of stroke and does not lock or hold the load if air is exhausted.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X565S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.