Airtac SE32 Standard Cylinder SE32X75SLB
The AirTAC Airtac SE32 Standard Cylinder SE32X75SLB is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 75mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke75 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X75SLB
The AirTAC SE32X75SLB is a double-acting, single-rod ISO 15552 profile cylinder delivering a 402 N push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. The LB foot mounting accessory provides rigid base anchoring for this 32 mm bore, 75 mm stroke unit.
This model includes a built-in magnet (-S) for non-contact position sensing with AirTAC CMSE reed or DMSE electronic switches. To absorb kinetic energy at the 75 mm stroke ends, it features field-adjustable pneumatic cushioning at both ends via a dedicated needle screw, letting technicians fine-tune the deceleration ramp to prevent hard end-stop impacts.
Airtac SE32 Standard Cylinder SE32X75SLB Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X75SLB |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X75SLB
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X75SLB Is Used
PCB Edge Guiding
Positions guide rails on a conveyor handling printed circuit boards, using the 402 N push force and 75 mm stroke to gently align lightweight electronics without crushing components.
Small Carton Flap Folding
Actuates a mechanical arm to tuck inner flaps on small pharmaceutical cartons, leveraging the adjustable end cushions to ensure soft, damage-free motion at cycle end.
Pneumatic Pick-and-Place
Drives the vertical Z-axis on a small pick-and-place gantry for electronic component assembly, using the built-in magnet to trigger DMSE sensors for precise stroke confirmation.
Is the Airtac SE32 Standard Cylinder SE32X75SLB the Right Cylinder?
Selecting the SE32X75SLB is optimal when a 402 N thrust at 0.5 MPa fits your payload, but you must verify load-holding requirements: a standard double-acting cylinder drifts when air is removed or the valve centers, so an external pilot-operated check valve or a BSE rod-lock variant is required for fail-safe holding. If you need less force, stepping down to the 40 mm bore yields 628 N push at 0.5 MPa, while stepping up to the 50 mm bore provides 982 N. As a true ISO 15552 profile cylinder, it offers a drop-in dimensional replacement for any standard 32 mm bore, 75 mm stroke, PT1/8 ported ISO cylinder, sharing standardized LB mounting hardware.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X75SLB FAQ
The 32 mm bore generates a push force of 402 N and a pull force of 345 N at 0.5 MPa. At 0.7 MPa, the push force is 563 N, and the maximum push force is 82 kgf at 1.0 MPa.
Yes, the SE32X75SLB is dimensionally interchangeable per ISO 15552 standards, matching the 32 mm bore, 75 mm stroke, PT1/8 port, and LB foot mount footprint of equivalent profile cylinders, allowing a seamless drop-in retrofit.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X75SLB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.