Airtac SE32 Standard Cylinder SE32X80SH
The AirTAC Airtac SE32 Standard Cylinder SE32X80SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 80mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke80 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X80SH
The AirTAC SE32X80SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for compact, high-temperature tasks. It yields 402 N of push force at 0.5 MPa across an 80 mm stroke. The square extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant housing that mounts cleanly in confined spaces. A built-in magnet enables position tracking with CMSE reed or DMSE electronic sensors.
Equipped with a Viton (FKM) seal, this unit reliably operates in environments up to 150 C. The field-adjustable pneumatic cushioning at both ends lets technicians dial in end-stop deceleration via a set screw, protecting payloads during high-speed 30-800 mm/s cycles.
Airtac SE32 Standard Cylinder SE32X80SH Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X80SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 80 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X80SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X80SH Is Used
Injection Mold Extraction
Handles 402 N push to positively eject small plastic parts from 150 C mold zones, leveraging the FKM seal to resist thermal degradation.
Heat-Seal Jaw Actuation
Drives compact sealing jaws at 30-800 mm/s, using the adjustable end cushions to softly arrest the 80 mm stroke without crushing packaging film.
Lab Oven Door Mechanism
Opens and closes high-temperature chamber doors, where the Viton seal maintains integrity up to 150 C and the sensor magnet tracks door position.
Is the Airtac SE32 Standard Cylinder SE32X80SH the Right Cylinder?
This 32 mm bore generates 402 N push at 0.5 MPa. If you need less force, there is no smaller ISO 15552 standard bore; if your application demands more power, step up to the 40 mm bore, which provides 628 N push at 0.5 MPa. The 80 mm stroke is well below the side-load threshold, but always mount rigidly to prevent rod-bearing bending.
For retrofits, match the 32 mm bore, 80 mm stroke, PT1/8 port, and your required mounting accessory. The -S magnet is included for CMSE / DMSE sensors. Remember, the adjustable air cushion only decelerates the piston near stroke end; it does not hold loads. If unpowered drift risks safety, integrate an external rod lock or pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X80SH FAQ
At 0.5 MPa, the push force is 402 N and the pull force is 345 N. At 0.7 MPa, the push force is 563 N. The maximum push force is 82 kgf at 1.0 MPa.
Yes. The SE32X80SH is dimensionally interchangeable per ISO 15552, allowing it to drop-in replace other standard profile cylinders. It uses a PT1/8 port and an M10x1.25 rod thread.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X80SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.