Airtac SE32 Standard Cylinder SE32X95
The AirTAC Airtac SE32 Standard Cylinder SE32X95 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 95mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke95 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X95
The AirTAC SE32X95 is a double-acting single-rod ISO 15552 profile cylinder featuring a 32 mm bore and a 95 mm stroke. Because 95 mm falls outside the standard stroke list, this unit is supplied as a non-standard, made-to-order configuration. It delivers 402 N of push force and 345 N of pull force at 0.5 MPa, peaking at 82 kgf at 1.0 MPa.
The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against frames. Adjustable pneumatic cushioning at both ends allows you to tune end-of-stroke deceleration via a set screw, softening hard impacts at operating speeds up to 800 mm/s. This specific SKU lacks the -S magnet option, so it is not equipped for AirTAC CMSE or DMSE position sensing without modification.
Airtac SE32 Standard Cylinder SE32X95 Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X95 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 95 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X95
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×95 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X95 Is Used
Lab Sample Dispensing
Drives a 402 N push to actuate small fluidic valves on analytical instruments, utilizing the 95 mm stroke to retract the sampling probe safely.
PCB Edge Trimming
Extends a lightweight cutting blade across a 95 mm path, relying on the tie-rod-free profile body to mount flush within dense electronics assembly cells.
Small Carton Flap Folding
Cycles at 30-800 mm/s to tuck minor flaps on pharmaceutical cartons, with adjustable air cushions softening the repetitive end-of-stroke stops.
Is the Airtac SE32 Standard Cylinder SE32X95 the Right Cylinder?
Delivering 402 N push at 0.5 MPa, the 32 mm bore fits light-duty actuation. If your payload is lighter, stepping down to the 25 mm bore yields 245 N push, while upgrading to the 40 mm bore provides 628 N push for heavier resistance. As a standard double-acting cylinder, it does not hold position or load when air is exhausted or the valve is centered—the piston drifts. For static holding, consider a BSE rod lock or external pilot-operated check valve.
For ISO 15552 retrofits, match the 32 mm bore, 95 mm stroke, PT1/8 port, and your required mounting accessory (Basic, LB, or FA). If you need position feedback, specify the -S magnet option for CMSE/DMSE switches. Since the 95 mm stroke is non-standard, expect a made-to-order lead time.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X95 FAQ
At 0.5 MPa, the SE32X95 provides 402 N push and 345 N pull. At 0.7 MPa, push increases to 563 N, with a maximum push of 82 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, the SE32X95 is dimensionally interchangeable per ISO 15552, serving as a drop-in replacement for other ISO 15552 profile cylinders. It features a PT1/8 port and a 12 mm rod with an M10x1.25 thread.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X95
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.