
The AirTAC SE40 Standard Cylinder SE40X10 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 10mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X10 is a double-acting single-rod ISO 15552 profile cylinder engineered for short-stroke actuation, delivering 628 N of push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, flush-mounting body that resists corrosion and simplifies fixture integration. This clean profile is ideal for tight machinery envelopes where space is at a premium.
This specific SKU is configured without a piston magnet, meaning it is ready for purely mechanical duty without position sensing. To tailor end-of-stroke impact, the cylinder features a field-adjustable air cushion at both ends via a setscrew, allowing you to fine-tune deceleration rather than relying on a fixed bumper. If your sequence later requires electronic confirmation, you would step up to an -S designated variant to host CMSE or DMSE sensors.
| Model | Airtac SE40 Standard Cylinder SE40X10 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 10 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the precise 628 N push and 10 mm travel needed to eject printed circuit boards from assembly fixtures without damaging delicate traces.
Executes rapid, short-stroke flap folding on packaging lines where the compact 40 mm bore fits neatly between conveyor rollers.
Acts as a short-stroke hard stop for positioning thin sheet metal panels at a press infeed, leveraging the rigid 16 mm rod to absorb sudden side impacts.
Selecting the SE40X10 makes sense when you need a compact 10 mm stroke with moderate force. If your application requires less energy, stepping down to the 32 mm bore drops the 0.5 MPa push to 402 N. Conversely, if you need to drive heavier loads, stepping up to the 50 mm bore increases that push to 982 N. Because this is a standard ISO 15552 footprint, it serves as a direct dimensional replacement for comparable profile cylinders, utilizing the same PT1/4 port and standard mounting accessories.
Keep in mind that a plain double-acting cylinder does not hold its position if air pressure is lost or the valve centers; the piston will drift. The adjustable air cushion only decelerates the piston near the stroke end and functions purely as a shock absorber, not as a locking mechanism. For any load-holding safety requirement, explore a BSE rod-lock variant or an external pilot-operated check valve.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push increases to 879 N. The maximum push is 128 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.
Yes, the SE40X10 is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can use it as a direct replacement for other ISO 15552 profile cylinders, matching the bore, stroke, PT1/4 port, and mounting interface exactly.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.