
The AirTAC SE40 Standard Cylinder SE40X115 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 115mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X115 is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver 628 N of push force and 528 N of pull force at 0.5 MPa. Driven by filtered air over a 115 mm stroke, it operates efficiently between 0.15 and 1.0 MPa. This bore size utilizes a PT1/4 port and a 16 mm hard-chrome plated rod, striking an optimal balance for medium-duty actuation tasks.
Its square extruded aluminum barrel eliminates external tie rods, yielding a smooth, compact footprint that resists corrosion and allows flush mounting on machinery. The cylinder features field-adjustable pneumatic cushioning at both ends, enabling technicians to fine-tune end-of-stroke deceleration via a set screw to minimize impact wear. Note that this specific SKU lacks a built-in magnet, so it does not support direct piston-position sensing without modification.
| Model | Airtac SE40 Standard Cylinder SE40X115 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 115 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×115 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the folding mechanism on case erectors, using the 115 mm stroke to quickly pop and square corrugated blanks at a steady 628 N push force.
Actuates routing gates on modular conveyor lines, where the compact tie-rod-free profile mounts flush to the aluminum frame without snagging passing parcels.
Secures lighter housings during machining or assembly, benefiting from the field-adjustable end cushions to soften hard stops during rapid cycling.
When sizing this 40 mm bore actuator, compare its 628 N push at 0.5 MPa against your load requirements. If your application demands less force, stepping down to the 32 mm bore yields 402 N of push, while moving up to the 50 mm bore provides 982 N. Because this is a standard double-acting cylinder, it will not hold a load in place if air pressure is lost or the valve is centered; a load-holding requirement dictates the BSE rod-lock variant or an external pilot-operated check valve.
For a 115 mm stroke, the 16 mm rod and M12x1.25 thread handle moderate side loads adequately, though long unsupported strokes exceeding 300 mm would require an external guide to prevent rod-bearing bending. As a true ISO 15552 profile cylinder, it is dimensionally interchangeable with other ISO 15552 cylinders, allowing you to retrofit existing setups using identical mounting hardware, PT1/4 ports, and standard accessories without machining.
Quick checklist
The SE40X115 generates 628 N of push force and 528 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 879 N. The maximum push force is 128 kgf when operated at the maximum pressure of 1.0 MPa.
Yes, the SE40X115 features a standardized ISO 15552 / VDMA 24562 mounting interface, making it dimensionally interchangeable with other ISO 15552 profile cylinders. You can drop it into existing setups using the same mounting hardware and PT1/4 port connections.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.