
The AirTAC SE40 Standard Cylinder SE40X12S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 12mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X12S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a 628 N push at 0.5 MPa. Its extruded aluminum square barrel omits external tie rods entirely, yielding a flush, corrosion-resistant body that mounts cleanly in tight spaces.
Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable air cushioning at both ends allows you to tune deceleration via a set screw, protecting your tooling from hard end-stop impacts.
| Model | Airtac SE40 Standard Cylinder SE40X12S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 12 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×12 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the short 12 mm stroke and 628 N push to safely eject populated printed circuit boards from test fixtures without damaging delicate components.
Drives a compact mechanical arm to fold minor flaps on packaging lines, relying on the DMSE electronic sensor to confirm stroke completion.
Pushes lightweight plastic bottles or hardware across a conveyor belt, where the smooth tie-rod-free profile prevents snagging on adjacent tooling.
This 40 mm bore provides 628 N of push force at 0.5 MPa. If your payload is lighter, you can step down to the 32 mm bore (402 N push); for heavier loads, step up to the 50 mm bore (982 N push). The 12 mm stroke is highly compact, making it perfect for short clamping or ejecting motions.
Because it is a standard double-acting cylinder, it will drift if air pressure is lost or the valve is centered, so it cannot hold a load safely without live pressure. For position holding, consider a BSE rod lock variant. As a true ISO 15552 profile cylinder, it serves as a direct dimensional replacement for any comparable standard cylinder using the same PT1/4 port and mounting accessories.
Quick checklist
At 0.5 MPa, it provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force is 879 N. The maximum push force is 128 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.
Yes. The SE40X12S is dimensionally interchangeable per ISO 15552. You can use it as a direct replacement for other 40 mm bore ISO 15552 profile cylinders, provided your mounting hardware and PT1/4 port match.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.