
The AirTAC SE40 Standard Cylinder SE40X140S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 140mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X140S is a double-acting single-rod profile cylinder delivering 628 N of push force at 0.5 MPa and 879 N at 0.7 MPa. Built to the ISO 15552 dimension standard, its square extruded aluminum barrel omits external tie rods, yielding a compact body that mounts flush against machine frames while resisting surface corrosion.
This 40 mm bore unit travels a 140 mm stroke and includes a built-in magnet (-S) for non-contact position sensing with AirTAC CMSE reed or DMSE electronic switches. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard mechanical stops during high-speed 30-800 mm/s cycling.
| Model | Airtac SE40 Standard Cylinder SE40X140S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 140 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×140 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 628 N of extend force at 0.5 MPa to secure aluminum housings inside CNC machining centers, utilizing the 140 mm stroke to clear the work envelope during part changes.
Cycles at 30-800 mm/s to fold corrugated cardboard flaps on continuous flow packaging lines, where the adjustable cushion softens the end stop to prevent crushing the board.
Extends 140 mm to push sorted parcels from a main conveyor belt onto a secondary routing chute, using the -S magnet to trigger DMSE sensors for transfer confirmation.
The 40 mm bore yields 628 N push at 0.5 MPa. If your mechanism needs less force, stepping down to the 32 mm bore yields 402 N push; scaling up to the 50 mm bore provides 982 N push. Because this is a standard double-acting cylinder, it does not hold loads if air pressure drops or the valve centers—use a BSE rod lock for fail-safe holding. The PT1/4 port and M12x1.25 rod thread match standard ISO 15552 mounting accessories. For this 140 mm stroke, the 16 mm rod handles standard side loads, but long unsupported strokes require an external guide to prevent rod-bearing bending.
Quick checklist
At 0.5 MPa, the 40 mm bore provides 628 N push and 528 N pull. At 0.7 MPa, push increases to 879 N. The maximum rated push force is 128 kgf at 1.0 MPa.
Yes, the SE40X140S is dimensionally interchangeable per ISO 15552, matching standardized mounting and pilot dimensions. You can use it as a direct replacement for other ISO 15552 profile cylinders using existing mounting hardware and PT1/4 ports.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.