
The AirTAC SE40 Standard Cylinder SE40X170S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 170mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X170S is a double-acting single-rod ISO 15552 profile cylinder engineered for mid-range actuation, delivering a push force of 628 N and a pull force of 528 N at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while retaining the standardized ISO 15552 footprint.
Equipped with a built-in magnet (-S), this unit directly supports AirTAC CMSE reed and DMSE electronic position sensors along the three integrated sensor grooves. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-speed 30-800 mm/s cycling.
| Model | Airtac SE40 Standard Cylinder SE40X170S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 170 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×170 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the precise 628 N push force required to fold corrugated cardboard flaps on high-speed packaging lines without crushing the box structure.
Utilizes the 170 mm stroke to actuate routing gates on conveyor systems, redirecting pallets into secondary packaging lanes.
Leverages the built-in -S magnet with DMSE electronic sensors to verify exact 170 mm extension for repeatable printed circuit board testing clamps.
When sizing this 40 mm bore, compare its 628 N push at 0.5 MPa against the smaller 32 mm bore (402 N push) for lighter duties, or step up to the 50 mm bore (982 N push) if your payload demands greater thrust. Because this model features a 170 mm stroke, it remains well within the side-load safety margin of the Ø16 mm rod and M12x1.25 thread, though external guides are always recommended for rigid lateral stability. As a standard ISO 15552 cylinder with a PT1/4 port, it serves as a direct dimensional replacement for any equivalent profile cylinder, utilizing standard mounting accessories and the -S magnet for seamless sensor integration.
Quick checklist
The SE40X170S generates 628 N push and 528 N pull at 0.5 MPa, 879 N push at 0.7 MPa, and a maximum push of 128 kgf at 1.0 MPa. It features a PT1/4 port and operates at speeds between 30-800 mm/s.
No, the SE40X170S is a standard double-acting cylinder and will drift if air is exhausted or valve pressure is lost. The adjustable air cushion only decelerates the piston near stroke end and does not function as a locking mechanism; for load holding, consider a BSE rod lock variant or an external pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.