verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE40 Standard Cylinder SE40X190S

The AirTAC SE40 Standard Cylinder SE40X190S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 190mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ40 mm
  • Stroke190 mm
  • Port sizePT1/4
  • Acting typeDouble acting
  • Rod threadM12×1.25
  • CushionAdjustable, 30 mm
$67.43 $74.93Save 10% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SE40 stroke, mounting and version on one page All SE40 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SE40 Standard Cylinder SE40X190S

The AirTAC SE40X190S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a push force of 628 N at 0.5 MPa and extending up to 879 N at 0.7 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing fewer crevices to debris.

Equipped with a built-in position magnet (-S), this unit seamlessly interfaces with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable pneumatic cushioning at both ends allows technicians to tune the deceleration of the 190 mm stroke via a set screw, softening hard impacts without relying on fixed rubber bumpers.

Airtac SE40 Standard Cylinder SE40X190S Technical Specifications

ModelAirtac SE40 Standard Cylinder SE40X190S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ40 mm
Stroke190 mm
Acting typeDouble acting
Port sizePT1/4
Rod threadM12×1.25
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm
Max strokeUp to 1200 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø40mm)

PressurePush forcePull force
0.5 MPa628 N528 N
0.7 MPa880 N—
Max (@1.0 MPa)128 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE40 Standard Cylinder SE40X190S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
40Bore size in mm.
×190Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE40 Standard Cylinder SE40X190S Is Used

conveyor_belt

Package Sorting Diverter

Utilizes the 190 mm stroke and 628 N push force to rapidly deflect corrugated cardboard cartons on a high-speed logistics sorting line.

packaging

Film Roll Tensioning Arm

Maintains precise tension on shrink-wrap machinery, relying on the -S magnet and DMSE sensors to confirm arm positioning.

view_module

PCB Test Fixture Clamp

Applies 528 N of retract pull force to secure delicate printed circuit boards within an automated testing station without crushing the substrate.

Is the Airtac SE40 Standard Cylinder SE40X190S the Right Cylinder?

Choosing this 40 mm bore makes sense when your application requires roughly 628 N of push force at 0.5 MPa. If you need less power, stepping down to the 32 mm bore yields 402 N of push force, while moving up to the 50 mm bore provides a significantly higher 982 N of push force at the same pressure. Because this cylinder uses a PT1/4 port and a 16 mm rod, it shares standardized ISO 15552 mounting dimensions, allowing a direct retrofit for other ISO cylinders using identical FA flanges or LB foot brackets.

Since the stroke is 190 mm, the unsupported piston rod experiences leverage forces during operation; incorporating an external guide rail is recommended to prevent rod-bearing bending under heavy lateral loads. Furthermore, remember that the adjustable air cushion only decelerates the piston near the end of its travel—it does not lock or hold the load. If your process requires position holding without live air pressure, you must integrate a pilot-operated check valve or switch to a BSE rod-lock variant.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE40 Standard Cylinder SE40X190S FAQ

At 0.5 MPa, the push force is 628 N and the pull force is 528 N. At 0.7 MPa, the push force increases to 879 N. The maximum push force is 128 kgf when operated at the maximum rated pressure of 1.0 MPa.

Yes, it is dimensionally interchangeable per ISO 15552, matching standard 40 mm bore mounting centers and PT1/4 ports. However, it does not hold position pneumatically; the adjustable cushion only decelerates the piston near stroke end, so an external rod lock is needed to hold loads without air pressure.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE40 Standard Cylinder SE40X190S

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SE40X190S and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.