
The AirTAC SE40 Standard Cylinder SE40X230S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 230mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X230S is a double-acting, single-rod ISO 15552 profile cylinder delivering 628 N of push force at 0.5 MPa. Driven by a 16 mm hard-chrome rod with a PT1/4 port, it provides 230 mm of travel and accepts air at 0.15-1.0 MPa.
This unit includes a built-in magnet for non-contact position sensing using AirTAC CMSE reed or DMSE electronic switches. The extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant body that mounts cleanly into tight machine cells, while field-adjustable pneumatic cushioning at both ends softens end-of-stroke impacts.
| Model | Airtac SE40 Standard Cylinder SE40X230S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 230 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×230 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Routes plastic containers on a 230 mm stroke using 628 N of push force, relying on the flush aluminum profile to resist washdown corrosion.
Folds cardboard flaps on packaging machinery, using the built-in magnet to trigger a DMSE electronic sensor for precise timing.
Pushes small metal blanks out of a die with 879 N at 0.7 MPa, utilizing the field-adjustable cushion to soften hard end stops.
If 628 N of push is insufficient, stepping up to the 50 mm bore yields 982 N at 0.5 MPa; if you need less force, the 32 mm bore provides 402 N. Because this is a 230 mm stroke exceeding 300 mm is not the case here, but always verify rod-bearing bending on long strokes and use an external guide for heavy radial loads. As a dimensionally interchangeable ISO 15552 component, it drops directly into existing foot, flange, or trunnion hardware. Remember that the adjustable air cushion only decelerates the piston near stroke end; if air is lost, the load drifts, requiring a BSE rod lock for static holding.
Quick checklist
At 0.5 MPa, the push force is 628 N and the pull force is 528 N. At 0.7 MPa, the push force reaches 879 N. The maximum push force is 128 kgf at 1.0 MPa.
No, the SE40X230S is a standard double-acting cylinder and the piston will drift if air is lost or exhausted. The adjustable air cushion only decelerates the piston near the end of stroke; it does not act as a brake. For position holding, use a BSE series rod lock or an external pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.