
The AirTAC SE40 Standard Cylinder SE40X255S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 255mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X255S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a 628 N push at 0.5 MPa. Its 255 mm stroke falls outside the standard list, making it a non-standard made-to-order configuration tailored for specific travel requirements. The extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion.
Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable air cushioning at both ends allows technicians to tune the deceleration of the 16 mm rod, softening hard impacts at high cycling speeds.
| Model | Airtac SE40 Standard Cylinder SE40X255S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 255 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×255 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 255 mm stroke to push product lanes on a packaging line, relying on the 628 N push force to deflect heavy glass bottles without stalling.
Cycles the sliding safety guard on a CNC turning center, using the -S magnet and DMSE electronic sensors to confirm door closure before the spindle starts.
Tucks the side flaps of corrugated cartons on a continuous flow wrapper, tuning the adjustable air cushion to prevent tearing the cardboard at stroke end.
When sizing this 40 mm bore, you can step down to the 32 mm bore for a lighter 402 N push at 0.5 MPa, or step up to the 50 mm bore for a heavier 982 N push. This SE40X255S features a PT1/4 port, a 16 mm rod, and the -S magnet for position sensing. Because the 255 mm stroke is non-standard, expect a made-to-order lead time. To retrofit an existing fixture, its ISO 15552 mounting interface allows direct replacement using standard FA, LB, or TC accessories.
With a 255 mm stroke, the unsupported rod length increases the risk of side-load bending on the front bearing. For applications exerting lateral forces, incorporate an external guide rail to prevent premature seal wear. Note that a plain SE cylinder drifts when air pressure is lost; if the machine must hold a load safely during an exhaust or power failure, specify a BSE rod lock variant instead.
Quick checklist
The SE40X255S delivers a push force of 628 N and a pull force of 528 N at 0.5 MPa. At 0.7 MPa, the push force is 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operating speed ranges from 30-800 mm/s.
Yes, the SE40X255S is dimensionally interchangeable per ISO 15552. You can use it as a direct replacement for other ISO 15552 profile cylinders of the same bore and stroke, reusing the existing mounting hardware and PT1/4 port connections.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.