
The AirTAC SE40 Standard Cylinder SE40X256S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 256mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X256S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 628 N push force at 0.5 MPa. Its 256 mm stroke is a non-standard made-to-order length, providing exact reach for specialized machine spacing where common increments fall short. The square extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush against frames.
Because this unit includes the -S magnet code, it is fully primed for AirTAC CMSE reed and DMSE electronic position sensing. You can fine-tune the end-of-stroke deceleration using the field-adjustable air cushioning at both ends, ensuring smooth stops even at the 30-800 mm/s operating speed range.
| Model | Airtac SE40 Standard Cylinder SE40X256S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 256 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×256 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Sorts PET bottles on a high-speed packaging line, using the 628 N push force and 256 mm stroke to actuate routing gates cleanly within tight machine enclosures.
Drives a lower cutting blade on an electronics assembly station, relying on the -S magnet and DMSE sensors to confirm precise 256 mm extension before shearing.
Folds corrugated cardboard flaps on a continuous packaging conveyor, utilizing the field-adjustable cushions to soften the end stops and prevent crushing the carton.
This 40 mm bore generates 628 N of push at 0.5 MPa. If your application requires less force, stepping down to the 32 mm bore yields 402 N; conversely, moving up to the 50 mm bore provides 982 N to handle heavier payloads. As a true ISO 15552 profile cylinder, it serves as a direct replacement for any standard 40 mm bore, 256 mm stroke unit, sharing identical mounting interface dimensions and PT1/4 ports.
Because the 256 mm stroke exceeds the standard catalog increments, it is supplied as a non-standard configuration. Furthermore, at this stroke length the 16 mm rod and M12x1.25 thread can experience increased bending moments under high side loads; incorporating an external guide rail is recommended to prevent premature rod-bearing wear. Note that the adjustable air cushion only decelerates the piston near stroke end and will not hold a load if air pressure is lost.
Quick checklist
At 0.5 MPa, the push force is 628 N and the pull force is 528 N. At 0.7 MPa, the push force increases to 879 N. The maximum rated push force is 128 kgf when operated at the 1.0 MPa pressure limit.
Yes, the SE40X256S is dimensionally interchangeable per ISO 15552. You can drop it into existing mounting hardware matching the standard 40 mm bore footprint, and it uses PT1/4 ports.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.