
The AirTAC SE40 Standard Cylinder SE40X276S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 276mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X276S is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding pneumatic tasks. It features a 40mm bore and a 276mm made-to-order stroke, generating 628 N of push force at 0.5 MPa and 879 N at 0.7 MPa. The extruded aluminum barrel design omits external tie rods, yielding a compact, flush-mounting body that resists corrosion and simplifies fixture integration.
This specific unit includes a built-in magnet (-S) for seamless operation with AirTAC CMSE reed and DMSE electronic position sensors. To protect the piston at high cycling speeds, field-adjustable air cushions at both ends allow you to tune end-of-stroke deceleration precisely, preventing hard impacts without relying on fixed rubber bumpers.
| Model | Airtac SE40 Standard Cylinder SE40X276S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 276 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×276 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Actuates a routing flap on a high-speed logistics conveyor, using the 276mm stroke to clear larger cartons while the 628 N thrust handles guide friction.
Pushes blank cardboard blanks into a folding frame, relying on the adjustable end cushions to soften stops during continuous 30-800 mm/s cycling.
Moves a test tube rack precisely between analysis stations, tracking the full 276mm travel via the built-in magnet and DMSE electronic sensors.
When sizing this 40mm bore actuator, compare its 628 N push at 0.5 MPa against the smaller 32mm bore (402 N push) for lighter duties, or step up to the 50mm bore (982 N push) if your load demands greater thrust. The 276mm stroke is a non-standard length, made-to-order for specific machine spacing requirements. Because this stroke exceeds 300mm, long unsupported piston travel increases side-load stress on the rod bearing; utilize an external guide rail to prevent binding and premature seal wear.
As a true ISO 15552 cylinder, the SE40X276S is dimensionally interchangeable with other ISO 15552 profile cylinders, ensuring a direct retrofit using standard mounting accessories. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not hold the load. If air pressure drops, the rod drifts, so add a BSE rod lock for fail-safe position holding. This model uses a PT1/4 port and an M12x1.25 rod thread.
Quick checklist
The SE40X276S has a non-standard 276mm stroke. At 0.5 MPa it provides 628 N push and 528 N pull force. At 0.7 MPa the push force is 879 N. The maximum push force is 128 kgf at 1.0 MPa operating pressure.
Yes. The SE40X276S is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact mounting footprint, PT1/4 port, and M12x1.25 rod thread of competing profile cylinders for seamless retrofitting.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.