
The AirTAC SE40 Standard Cylinder SE40X285S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 285mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X285S is a double-acting, single-rod ISO 15552 profile cylinder with a 40 mm bore and a 285 mm non-standard stroke. It generates 628 N of push force and 528 N of pull force at 0.5 MPa, making it well-suited for mid-range automation tasks. The extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This specific unit includes a built-in magnet (-S) for non-contact position sensing using AirTAC CMSE reed or DMSE electronic switches. Field-adjustable air cushions at both ends allow you to tune end-of-stroke deceleration for moving loads, while the PT1/4 port ensures standard pneumatic connectivity.
| Model | Airtac SE40 Standard Cylinder SE40X285S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 285 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×285 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Actuates a routing arm on a logistics conveyor, using the 628 N push force and 285 mm stroke to redirect medium-weight parcels between sorting lanes.
Drives the splicing mechanism on continuous-flow packaging lines, where the 528 N pull force securely tensions and cuts wrapping film during roll changes.
Positions a multi-position carousel in automated laboratory analyzers, relying on the built-in magnet to trigger DMSE electronic sensors for precise tube alignment.
Choosing this 40 mm bore makes sense when your application requires roughly 628 N of push at 0.5 MPa. If your load is lighter, stepping down to the 32 mm bore yields 402 N of push, conserving space and air. For heavier demands, stepping up to the 50 mm bore provides 982 N of push. Because the 285 mm stroke is a non-standard made-to-order length, expect a longer lead time than off-the-shelf strokes.
As a standard ISO 15552 cylinder, this model is dimensionally interchangeable with other ISO 15552 profile cylinders, simplifying retrofits. Note that at 285 mm of stroke, the 16 mm rod and bearing face increased bending moments under side loads; for offset loads, add an external guide to prevent premature wear. Also, the adjustable cushion only decelerates the piston near stroke end and will not hold a load if air pressure is lost.
Quick checklist
At 0.5 MPa, the SE40X285S provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force is 879 N, with a maximum push of 128 kgf at 1.0 MPa. Operating pressure ranges from 0.15 to 1.0 MPa, and speed ranges from 30 to 800 mm/s.
Yes. The SE40X285s features a standard ISO 15552 / VDMA 24562 mounting interface and PT1/4 ports, making it dimensionally interchangeable with other ISO 15552 profile cylinders for direct retrofits.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.