
The AirTAC SE40 Standard Cylinder SE40X330S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 330mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X330S is a double-acting, single-rod ISO 15552 profile cylinder engineered for mid-range actuation, delivering a 628 N push at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while maintaining the standardized ISO 15552 footprint.
Equipped with a built-in magnet (-S), this unit seamlessly integrates AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable pneumatic cushioning at both ends allows technicians to tune deceleration via a set screw, softening hard impacts during high-speed 30-800 mm/s cycling.
| Model | Airtac SE40 Standard Cylinder SE40X330S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 330 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×330 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Pushes cartons across a 330 mm transfer gap with 628 N of force at 0.5 MPa, relying on the built-in magnet for DMSE sensor timing.
Cycles rapidly at 30-800 mm/s to maintain fabric tension, using the adjustable end cushions to prevent frame-shaking end stops.
Acts as a 330 mm physical stop for incoming pallets, where the tie-rod-free extruded profile resists shop-floor debris and moisture.
Selecting the SE40X330S is optimal when your mechanism requires a 330 mm extension with a 628 N push at 0.5 MPa. If your payload is lighter, you can step down to the 32 mm bore offering 402 N push; if you need more authority, the 50 mm bore provides 982 N push. Because the 330 mm stroke creates leverage on the 16 mm rod, applying an external guide rail is recommended to prevent rod-bearing bending under heavy lateral loads.
This cylinder is dimensionally interchangeable per ISO 15552, serving as a direct replacement for other ISO 15552 cylinders while utilizing standard mounting accessories. Note that the adjustable air cushion only decelerates the piston near stroke end; it is not a locking mechanism, so loads will drift if air pressure is lost.
Quick checklist
The 40 mm bore generates a 628 N push and 528 N pull at 0.5 MPa, an 879 N push at 0.7 MPa, and a maximum 128 kgf push at 1.0 MPa. It features a PT1/4 port and a 16 mm hard-chrome rod.
No, the adjustable air cushion only decelerates the piston near the stroke end and does not lock the rod. If position holding is required without live air pressure, you must use an external rod lock or pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.