
The AirTAC SE40 Standard Cylinder SE40X425S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 425mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X425S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 628 N of push force at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing standardized ISO 15552 interface dimensions for seamless retrofitting.
Equipped with a built-in magnet (-S), this unit directly supports AirTAC CMSE reed and DMSE electronic position sensing for precise end-of-stroke verification. The 425 mm stroke is supported by a Ø16 mm piston rod with an M12x1.25 thread, and field-adjustable pneumatic cushioning at both ends allows technicians to tune end-stop deceleration for fast 30-800 mm/s cycles.
| Model | Airtac SE40 Standard Cylinder SE40X425S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 425 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×425 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 628 N of push at 0.5 MPa to actuate routing flaps on packaging lines, with the 425 mm stroke offering ample travel to fully clear the conveyor lane.
Ejects machined aluminum parts from a CNC enclosure using the M12x1.25 rod thread to attach a custom pusher plate, relying on DMSE sensors to confirm retraction.
Deploys a physical stop block at 425 mm to index wooden pallets on a roller conveyor, using adjustable end cushions to soften the impact of 30-800 mm/s cycling.
If your assembly requires less push force, stepping down to the 32 mm bore yields 402 N at 0.5 MPa, whereas stepping up to the 50 mm bore provides 982 N for heavier payloads. Because this is a 425 mm stroke, the unsupported rod length increases bending moments on the rod bearing; utilizing an external guide is strongly recommended to prevent side-load wear. As a standard double-acting cylinder, the SE40X425S does not hold loads pneumatically when air is exhausted—add a BSE rod lock for vertical position holding. It is dimensionally interchangeable with any ISO 15552 cylinder matching its 40 mm bore, 425 mm stroke, PT1/4 port, and chosen mounting accessory.
Quick checklist
The SE40X425S features a 40 mm bore and a 425 mm stroke. At 0.5 MPa it provides 628 N of push force and 528 N of pull force. At 0.7 MPa the push force is 879 N, and the maximum push force is 128 kgf at 1.0 MPa.
Yes. The SE40X425S is a true ISO 15552 profile cylinder with no external tie rods, making it dimensionally interchangeable with other ISO 15552 cylinders of the same bore and stroke. The built-in magnet also works directly with AirTAC CMSE and DMSE sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.