
The AirTAC SE40 Standard Cylinder SE40X485S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 485mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X485S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 628 N of push force and 528 N of pull force at 0.5 MPa. Driven by filtered air over a 485 mm stroke, it features a 16 mm hard-chrome piston rod and a PT1/4 port. Because it adheres to the standardized VDMA 24562 mounting footprint, this unit serves as a direct, direct replacement for any equipment already utilizing ISO 15552 cylinders, simplifying retrofits and procurement.
This specific model includes a built-in magnet (-S) for non-contact position sensing, seamlessly supporting AirTAC CMSE reed and DMSE electronic solid-state switches. The extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. Furthermore, field-adjustable pneumatic cushioning at both stroke ends allows technicians to dial in deceleration via a set screw, softening hard end stops during high-speed 30-800 mm/s operations.
| Model | Airtac SE40 Standard Cylinder SE40X485S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 485 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×485 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Cycles a 485 mm routing arm at 30-800 mm/s to redirect parcels on high-speed logistics sortation lines, utilizing the 628 N push force to overcome carton friction.
Drives a 485 mm vertical forming mechanism to open flat paperboard blanks, relying on the adjustable end cushions to prevent tearing during rapid 0.5 MPa retraction.
Actuates a 485 mm swing arm to position raw material blanks into machining centers, using the built-in magnet with DMSE sensors for precise end-of-stroke confirmation.
When sizing this 40 mm bore actuator, evaluate your thrust requirements against its 628 N push at 0.5 MPa. If your application demands less force, stepping down to the 32 mm bore yields 402 N of push, whereas scaling up to the 50 mm bore provides 982 N of thrust. Since this model features a 485 mm stroke, the 16 mm rod and thread interface face increased bending moments under side loads; for long unsupported strokes, integrating an external linear guide is strongly recommended to prevent premature rod-bearing wear.
As a standard double-acting cylinder, the SE40X485S relies on live air pressure to maintain its position. If air is exhausted or the directional valve is centered, the piston will drift and cannot hold a load. For applications requiring true position holding without constant pressure, consider the BSE series rod lock variant. To execute a precise ISO 15552 replacement, verify your existing bore, stroke, PT1/4 port, and mounting accessory (such as LB foot or FA front flange) to ensure a seamless direct fit.
Quick checklist
At 0.5 MPa, the SE40X485S provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N. The maximum push force is 128 kgf when operated at the 1.0 MPa pressure limit.
No, the SE40X485S is a standard double-acting cylinder and will drift if air is lost or the valve is centered. The adjustable air cushion at both ends only decelerates the piston near the stroke end and does not function as a locking brake. For load-holding, use an external rod lock like the BSE series.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.