
The AirTAC SE40 Standard Cylinder SE40X500SLB is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 500mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X500SLB is a double-acting, single-rod ISO 15552 profile cylinder engineered for a 500 mm stroke. It delivers a 628 N push force at 0.5 MPa, making it well-suited for mid-range actuation tasks. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This LB foot-mounted unit includes a built-in magnet for CMSE and DMSE position sensing. Field-adjustable air cushions at both ends allow technicians to dial in end-of-stroke deceleration, softening hard impacts during high-speed cycles.
| Model | Airtac SE40 Standard Cylinder SE40X500SLB |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 500 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×500 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 500 mm stroke to push cartons between parallel conveyor belts, relying on the 628 N push force to shift heavy boxes without stalling.
Steps test tubes into a centrifuge loading position, where the built-in S magnet triggers a DMSE electronic sensor for precise 500 mm travel confirmation.
Deploys a physical stop arm across a roller conveyor to halt incoming wooden pallets, absorbing kinetic energy through the adjustable end cushions.
Choosing the 40 mm bore provides 628 N of push at 0.5 MPa. If your assembly requires less force, stepping down to the 32 mm bore yields 402 N, while moving up to the 50 mm bore increases output to 982 N. Because this is a 500 mm stroke, the unsupported piston rod is prone to bending under heavy lateral loads; always pair it with an external guide rail to prevent rod-bearing wear.
For retrofitting, this cylinder shares the exact ISO 15552 mounting footprint and PT1/4 port of competing profile cylinders, allowing a direct replacement using the existing LB foot bracket and hardware. Note that a standard SE cylinder will drift if air pressure is lost; for position holding, consider the BSE rod lock variant.
Quick checklist
At 0.5 MPa, it provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force is 879 N. The maximum push force is 128 kgf when operated at the 1.0 MPa pressure limit.
Yes. The SE40X500SLB is dimensionally interchangeable per ISO 15552 standards, meaning it matches the standardized mounting interface, PT1/4 port, and 16 mm rod thread of other profile cylinders, enabling a direct retrofit using your existing LB foot bracket.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.