
The AirTAC SE40 Standard Cylinder SE40X50H is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 50mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X50H is a double-acting, single-rod ISO 15552 profile cylinder engineered for high-temperature pneumatics. It generates 628 N of push force and 528 N of pull force at 0.5 MPa, making it well-suited for compact actuation tasks. Because this specific SKU is built with an FKM (Viton) seal, it reliably operates in ambient temperatures up to 150 °C where standard TPU seals would fail.
The extruded aluminum barrel design omits external tie rods, yielding a smooth, corrosion-resistant exterior that mounts flush against machine frames. Field-adjustable pneumatic cushioning at both stroke ends allows technicians to tune end-of-stroke deceleration via a set screw, protecting the 16 mm rod during high-speed 50 mm strokes. Note that this configuration ships without a position magnet, so external CMSE or DMSE switches cannot be used without modification.
| Model | Airtac SE40 Standard Cylinder SE40X50H |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Suitable for hot molding environments up to 150 C, utilizing its 628 N push force to eject plastic parts from heated platens over a short 50 mm stroke.
Handles the 50 mm clamping stroke on thermal stamping machinery, where the Viton FKM seal resists degradation from proximity to heated platens.
Drives the sealing jaw actuation on continuous-motion shrink wrap equipment, maintaining 528 N pull force reliably in ambient heat near shrink tunnels.
If your thermal load does not exceed 70 °C, stepping down to the SE32X50 with its 402 N push at 0.5 MPa saves space, while moving up to the SE50X50 provides a robust 982 N push for heavier mechanisms. As a dimensionally interchangeable ISO 15552 cylinder, this 40 mm bore unit serves as a direct replacement for other standardized profile cylinders, utilizing a PT1/4 port and M12x1.25 rod thread. Keep in mind that the integrated air cushion only decelerates the piston near the stroke ends; it does not lock or hold the load if air pressure is lost. If your application requires end-position feedback, you must select a variant with the built-in -S magnet for CMSE or DMSE sensor compatibility.
Quick checklist
The SE40X50H provides a push force of 628 N and a pull force of 528 N at 0.5 MPa. At 0.7 MPa, the push force is 879 N. The maximum drive force is 128 kgf at the maximum operating pressure of 1.0 MPa.
Yes, this specific model uses an FKM (Viton) seal, expanding the operating temperature range from -20 °C up to 150 °C. Standard SE cylinders with TPU seals are limited to 80 °C, making this variant ideal for hot stamping or molding environments.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.