verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE40 Standard Cylinder SE40X55SH

The AirTAC SE40 Standard Cylinder SE40X55SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 55mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ40 mm
  • Stroke55 mm
  • Port sizePT1/4
  • Acting typeDouble acting
  • Rod threadM12×1.25
  • CushionAdjustable, 30 mm
$65.10 $72.60Save 10% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SE40 stroke, mounting and version on one page All SE40 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SE40 Standard Cylinder SE40X55SH

The AirTAC SE40X55SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for rigorous linear motion. It delivers 628 N of push force and 528 N of pull force at 0.5 MPa, utilizing a 16 mm rod and a PT1/4 port. Built with a square extruded aluminum barrel, the design eliminates external tie rods entirely, yielding a compact footprint that mounts flush against machinery while resisting corrosion.

This specific configuration includes an -S magnet for non-contact position sensing using AirTAC CMSE reed or DMSE electronic switches seated in the three-sided sensor grooves. The H seal designation equips the unit with a high-temperature FKM Viton seal, expanding the operating temperature range from -20 to +150 degrees Celsius for harsh thermal environments. Field-adjustable pneumatic cushioning at both stroke ends allows technicians to dial in end-of-stroke deceleration, softening hard mechanical stops during high-speed cycling.

Airtac SE40 Standard Cylinder SE40X55SH Technical Specifications

ModelAirtac SE40 Standard Cylinder SE40X55SH
SeriesSE ISO 15552 profile cylinder
Bore sizeØ40 mm
Stroke55 mm
Acting typeDouble acting
Port sizePT1/4
Rod threadM12×1.25
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm
Max strokeUp to 1200 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø40mm)

PressurePush forcePull force
0.5 MPa628 N528 N
0.7 MPa880 N—
Max (@1.0 MPa)128 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE40 Standard Cylinder SE40X55SH

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
40Bore size in mm.
×55Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE40 Standard Cylinder SE40X55SH Is Used

packaging

Thermoforming Film Feed

Drives the pulling and feeding mechanism for shrink-wrap films in heated packaging tunnels, where the 150 C FKM seal survives ambient radiating heat while providing 628 N of push force.

conveyor_belt

Hot End Product Divert

Actuates a diverting arm on a conveyor system routing cured rubber components, utilizing the 55 mm stroke and CMSE reed sensor magnet for rapid position confirmation.

straighten

Plastic Trim Press

Applies 528 N of retract force to press and straighten warm injection-molded automotive trim pieces, taking advantage of the field-adjustable cushion to prevent marking on soft surfaces.

Is the Airtac SE40 Standard Cylinder SE40X55SH the Right Cylinder?

When sizing this actuator, evaluate the 628 N push force at 0.5 MPa against your dynamic load. If your application requires less energy, stepping down to the 32 mm bore yields 402 N of push force. Conversely, scaling up to the 50 mm bore provides 982 N of push force for heavier mechanisms. Because this is a double-acting cylinder, it relies on continuous air pressure to hold position; if a load must be maintained during air loss or valve centering, a BSE rod lock variant is required rather than relying on the adjustable air cushion, which only decelerates the piston near the end of travel. As a true ISO 15552 profile cylinder, it serves as a dimensionally interchangeable direct replacement for other ISO 15552 cylinders, sharing standardized mounting hardware like FA front flanges or LB foot brackets. The PT1/4 port and M12x1.25 rod thread are set by the 40 mm bore standard.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE40 Standard Cylinder SE40X55SH FAQ

The SE40X55SH generates 628 N of push force and 528 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.

Yes, the SE40X55SH is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact mounting interface and can serve as a direct replacement for other ISO 15552 profile cylinders without altering your machine's mounting footprint.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE40 Standard Cylinder SE40X55SH

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SE40X55SH and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.