
The AirTAC SE40 Standard Cylinder SE40X60SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 60mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X60SN is a double-acting, single-rod ISO 15552 profile cylinder featuring a 40 mm bore and 60 mm stroke. It generates 628 N of push force and 528 N of pull force at 0.5 MPa, making it well-suited for mid-range industrial actuation. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This specific configuration includes a built-in magnet for non-contact position sensing with AirTAC CMSE reed or DMSE electronic switches, alongside an NBR seal for standard pneumatic duty. Field-adjustable air cushions at both stroke ends allow you to tune end-of-travel deceleration, preventing hard impacts during high-speed cycling.
| Model | Airtac SE40 Standard Cylinder SE40X60SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 60 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 628 N push and 60 mm travel needed to fold and secure corrugated carton flaps at high cycling speeds on packaging lines.
Actuates a short 60 mm diverter pop-up to route small packages on a conveyor belt, benefiting from the flush-mount no-tie-rod profile.
Ejects lightweight stamped or molded parts from a fixture, using the NBR seal and adjustable cushioning to ensure smooth, impact-free ejection.
With a 628 N push at 0.5 MPa, this 40 mm bore is a solid fit for moderate loads, but if your application requires less force, the 32 mm bore offers 402 N. For heavier demands, stepping up to the 50 mm bore provides 982 N of push. Because the 60 mm stroke is relatively short, side-load bending on the Ø16 mm rod bearing is minimal, though external guides are always recommended for rigid lateral loads. Remember that the adjustable air cushion only decelerates the piston near stroke end; it does not hold the load if air pressure is lost. For position holding, consider a BSE rod lock variant. As a true ISO 15552 cylinder, it serves as a dimensionally interchangeable direct replacement for other standard profile cylinders, utilizing a PT1/4 port and standard mounting accessories.
Quick checklist
At 0.5 MPa, the SE40X60SN delivers 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force is 879 N. The maximum operating pressure is 1.0 MPa, which yields a maximum push force of 128 kgf.
Yes, it is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting footprint and can replace other ISO 15552 profile cylinders. The built-in magnet (-S) is specifically designed to work with AirTAC CMSE reed switches and DMSE electronic sensors for end-position detection.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.