
The AirTAC SE40 Standard Cylinder SE40X64S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 64mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X64S is a double-acting single-rod profile cylinder operating on the ISO 15552 interface, delivering 628 N of push force at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. This design simplifies sensor placement along three integrated grooves.
Equipped with a built-in magnet (S option), this unit directly supports AirTAC CMSE reed and DMSE electronic solid-state switches for precise end-position detection. The cylinder features field-adjustable pneumatic cushioning at both ends, allowing technicians to tune end-of-stroke deceleration via a set screw to eliminate hard mechanical impacts during high-speed cycling.
| Model | Airtac SE40 Standard Cylinder SE40X64S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 64 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×64 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives folding mechanisms on packaging lines, utilizing the 628 N push force and 64 mm stroke to cleanly tuck flaps before tape application.
Actuates a routing gate on a conveyor system, where the compact tie-rod-free profile allows flush mounting into tight transfer zones.
Ejects small molded components from a press, using the DMSE electronic sensor to confirm retraction before the next machine cycle begins.
When sizing this 40 mm bore, you can step down to a 32 mm bore for 402 N push at 0.5 MPa, or step up to a 50 mm bore for 982 N push at 0.5 MPa. As a 64 mm stroke is a non-standard made-to-order length, expect a longer lead time compared to the 50 mm or 75 mm standard strokes. The PT1/4 port and M12x1.25 rod thread match standard ISO 15552 mounting accessories.
Because this is a double-acting cylinder, it will drift if air pressure is lost or the valve centers; it cannot hold a load without live pressure. If your application requires positive holding, consider a BSE rod lock variant or an external pilot-operated check valve.
Quick checklist
At 0.5 MPa, the push force is 628 N and the pull force is 528 N. At 0.7 MPa, the push force is 879 N. The maximum push force is 128 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes. The SE40X64S is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can use it as a direct replacement for other ISO 15552 profile cylinders, retaining your existing mounting hardware and PT1/4 port connections.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.