
The AirTAC SE40 Standard Cylinder SE40X650S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 650mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X650S is a double-acting single-rod profile cylinder built to ISO 15552 dimensions, delivering a push force of 628 N at 0.5 MPa. Its 650 mm stroke and 16 mm rod make it a solid choice for mid-range linear actuation. The square extruded aluminum barrel omits external tie rods, yielding a compact body that mounts flush and resists corrosion.
Because this unit includes the -S magnet, it is ready for CMSE reed or DMSE electronic position sensing along the integrated sensor grooves. You can fine-tune the pneumatic end-of-stroke deceleration via the adjustable cushioning screws at both ends, protecting your mechanisms from hard impacts.
| Model | Airtac SE40 Standard Cylinder SE40X650S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 650 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×650 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 650 mm stroke to push packaging pallets smoothly between parallel conveyor lines, relying on the 628 N push force to overcome sliding friction.
Deploys the adjustable pneumatic cushioning to gently fold heavy cardboard flaps prior to sealing, preventing sudden impacts that crush the carton edges.
Lifts empty plastic totes in automated storage systems, utilizing the integrated DMSE electronic sensors to confirm vertical positioning without physical stops.
When sizing this 40 mm bore, compare its 628 N push at 0.5 MPa against the 32 mm bore (402 N push) if your load is lighter, or step up to the 50 mm bore (982 N push) for heavier demands. As a standard ISO 15552 profile cylinder, it serves as a direct replacement for other ISO 15552 cylinders, matching the PT1/4 port and standard mounting accessories. To add position feedback, pair the built-in magnet with AirTAC CMSE or DMSE switches.
With a 650 mm stroke, the 16 mm piston rod experiences higher bending moments under side loads. To prevent premature rod-bearing wear, implement an external guide rail to support the load and keep lateral forces off the rod. Note that a plain SE cylinder will drift if air pressure is lost; if your application requires strict position holding, consider the BSE rod lock variant.
Quick checklist
At 0.5 MPa, the push force is 628 N and the pull force is 528 N. At 0.7 MPa, the push force is 879 N. The maximum push force is 128 kgf at 1.0 MPa, and the operating speed ranges from 30-800 mm/s.
Yes, the SE40X650S is dimensionally interchangeable per ISO 15552. You can drop it into existing mounts and use the standard PT1/4 porting, provided your mounting hardware matches the standard footprint.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.