verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE40 Standard Cylinder SE40X660S

The AirTAC SE40 Standard Cylinder SE40X660S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 660mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ40 mm
  • Stroke660 mm
  • Port sizePT1/4
  • Acting typeDouble acting
  • Rod threadM12×1.25
  • CushionAdjustable, 30 mm
$120.73 $128.23Save 5% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SE40 stroke, mounting and version on one page All SE40 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SE40 Standard Cylinder SE40X660S

The AirTAC SE40X660S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a push force of 628 N at 0.5 MPa and a maximum thrust of 128 kgf. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact body that mounts flush against machine frames while resisting corrosion.

Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable air cushioning at both ends allows technicians to tune the end-of-stroke deceleration, smoothly absorbing kinetic energy across the 660 mm travel.

Airtac SE40 Standard Cylinder SE40X660S Technical Specifications

ModelAirtac SE40 Standard Cylinder SE40X660S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ40 mm
Stroke660 mm
Acting typeDouble acting
Port sizePT1/4
Rod threadM12×1.25
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm
Max strokeUp to 1200 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø40mm)

PressurePush forcePull force
0.5 MPa628 N528 N
0.7 MPa880 N—
Max (@1.0 MPa)128 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE40 Standard Cylinder SE40X660S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
40Bore size in mm.
×660Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE40 Standard Cylinder SE40X660S Is Used

conveyor_belt

Pallet Diverters

Uses the 628 N extend force to push heavy wooden pallets cleanly across transfer lines without stalling under friction.

packaging

Carton Flap Folders

Leverages the 660 mm stroke to reach across wide corrugated cartons, tucking top flaps prior to tape sealing.

warehouse

Vertical Lift Gates

Actuates mezzanine safety gates, utilizing the adjustable cushions to softly decelerate the heavy barrier at stroke end.

Is the Airtac SE40 Standard Cylinder SE40X660S the Right Cylinder?

If your application requires less thrust, stepping down to the 32 mm bore yields 402 N of push at 0.5 MPa; conversely, moving up to the 50 mm bore provides 982 N. This SE40X660S includes a PT1/4 port, a 16 mm rod, and the -S magnet for position sensing.

Because the 660 mm stroke creates a long lever arm on the rod bearing, side loads will induce bending moments that accelerate wear. An external guide rail should be installed to support the load and prevent premature seal failure. Note that this cylinder relies on live air pressure; if air is lost, the piston will drift and cannot hold a load.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE40 Standard Cylinder SE40X660S FAQ

At 0.5 MPa, the push force is 628 N and the pull force is 528 N. At 0.7 MPa, the push force is 879 N. The maximum push force is 128 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.

Yes. The SE40X660S shares the exact ISO 15552 mounting interface and PT1/4 port sizing, making it a direct dimensional replacement for other standard profile cylinders. It uses standard mounting accessories and requires no custom machining.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE40 Standard Cylinder SE40X660S

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SE40X660S and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.