
The AirTAC SE40 Standard Cylinder SE40X80S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 80mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X80S is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver 628 N of push force at 0.5 MPa. Its square extruded aluminum barrel entirely eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames without protruding hardware. Equipped with a built-in magnet, it supports direct mounting for AirTAC CMSE reed and DMSE electronic position sensors along the standardized body grooves.
Field-adjustable pneumatic cushioning at both stroke ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard mechanical stops during high-speed 30-800 mm/s cycling. Operating across a 0.15-1.0 MPa pressure range, this 40 mm bore unit features a 16 mm rod and a PT1/4 port, making it dimensionally interchangeable with other ISO 15552 cylinders for seamless retrofits.
| Model | Airtac SE40 Standard Cylinder SE40X80S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 80 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 628 N of push force at 0.5 MPa to reliably open and fold corrugated carton flaps on continuous packaging lines, utilizing the 80 mm stroke for rapid actuation.
Pivots routing gates to sort small parcels on conveyor belts, where the -S magnet triggers DMSE sensors to confirm divert position before downstream accumulation.
Secures aluminum workpieces during CNC machining, using the adjustable end cushions to prevent impact bounce and maintain clamping repeatability at 0.7 MPa.
When sizing this 40 mm bore model, stepping down to the 32 mm variant reduces the 0.5 MPa push force to 402 N, whereas stepping up to the 50 mm bore increases it to 982 N for heavier payloads. The integrated -S magnet enables precise end-of-stroke detection using CMSE or DMSE switches without additional brackets. Remember that the adjustable air cushion only decelerates the piston near stroke end; it does not hold a load. If your application loses air pressure or centers the valve, the piston will drift. For static holding, consider a BSE rod lock variant or an external pilot-operated check valve. With an 80 mm stroke, side-load bending on the 16 mm rod bearing is minimal, though long unsupported strokes require an external guide.
Quick checklist
The SE40X80S generates 628 N push and 528 N pull at 0.5 MPa, 879 N push at 0.7 MPa, and reaches a maximum push of 128 kgf at 1.0 MPa operating pressure.
Yes, the SE40X80S shares the exact ISO 15552 / VDMA 24562 mounting interface and dimensions, allowing it to interchange with other ISO 15552 profile cylinders using existing mounting hardware and PT1/4 ports.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.