
The AirTAC SE40 Standard Cylinder SE40X95S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 95mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X95S is a double-acting, single-rod ISO 15552 profile cylinder delivering 628 N of push force at 0.5 MPa. Driven by filtered air, it operates seamlessly within a 0.15-1.0 MPa pressure range. Its square extruded aluminum barrel omits external tie rods entirely, creating a smooth, corrosion-resistant body that mounts flush against machine frames to save valuable space.
Equipped with a built-in magnet (-S), this unit interfaces directly with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable pneumatic cushioning at both ends allows technicians to fine-tune end-stop deceleration for a 95 mm stroke, ensuring smooth operation without relying on fixed rubber bumpers.
| Model | Airtac SE40 Standard Cylinder SE40X95S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 95 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×95 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 628 N of push force at 0.5 MPa to reliably fold and seal corrugated carton flaps during automated packaging line operations.
Uses its 95 mm stroke and built-in magnet to actuate routing gates, seamlessly directing parcels between conveyor belt sections.
Delivers precise 528 N retract force to press small metal or plastic components into sub-assemblies without damaging the base material.
If your application requires less force, stepping down to the 32 mm bore yields 402 N of push at 0.5 MPa, while moving up to the 50 mm bore provides 982 N for heavier loads. As a standard ISO 15552 profile cylinder, this model is dimensionally interchangeable with other ISO 15552 cylinders, allowing you to use existing mounting hardware like FA front flanges or LB foot brackets without redesigning your framework. Remember that a standard SE cylinder relies on live air pressure to hold its position; if your process loses air, the piston will drift, and you should explore a BSE rod lock variant for secure holding.
Quick checklist
At 0.5 MPa, the SE40X95S generates 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N. The maximum allowable push force is 128 kgf when operating at the maximum rated pressure of 1.0 MPa.
Yes, the SE40X95S is dimensionally interchangeable per ISO 15552 standards. It shares the standardized mounting interface and PT1/4 port location, allowing a direct replacement for other ISO 15552 profile cylinders using your existing mounting accessories.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.